783667
2
Zoom out
Zoom in
Previous page
1/2
Next page
Introduction Battery installation
Probe connection
How to measure
Preview Default Setting
How to Change Default Setting
Rossmax Handheld Pulse Oximeter is used to measure oxygen saturation in blood
(SpO2) and pulse rate, also to issue warnings immediately. It is a non-invasive
device intended for spot-check of adults, child, and infants with corresponding
probe applied at home, hospital and clinics. The probe contains a dual light
source and a photodetector.
Attention: Consult the accompanying documents. Please read this manual
carefully before use. Please be sure to keep this manual.
1. Use thumb to slide battery cover out.
2. Insert or replace 4 “AA” batteries according to the (+/-) polarity.
Caution: Need to replace when the batteries icon “ ” is blinking on display/
while pressed the function button and nothing appears on display.
Caution: Batteries may leak or explode if used or disposed of improperly. Remove
batteries if the device will be stored for long time. Do not use different
types or brand of batteries at the same time.
Rossmax PA100/ PC100 or compatible probe is used. (Please install carefully.)
Caution: It may damage the efficiency of the device if not apply with a Rossmax
compatible probe.
1. Press the Power On button for 1 second, when the device activates, the beep
sound will last for 2 second.
Note: After the device activates, the software version will pop up directly. For first
time activates, it will directly jump to time setting. (Please refer to setting
instruction.)
2. Information of software version appears; insert one finger to probe, nail side up,
for self-test.
Notes: The device will turn itself off automatically after 1 minute idling with two
beep sounded.
3. The pulse strength shows “ , pulse oximeter begins its measurement.
Notes: The heartbeat is sounded though the buzzer. If need to become silence
mode, press the sound button and the LCD screen will have the sound
icon shown. If need the heartbeat sound, press the sound button to exit.
4. Your SpO2 and pulse rate values will appears on the screen after few seconds.
Notes: 1. Don’t remove your finger until the measurement is completed.
2. Any other problems or unrecognized icon, please refer to trouble shooting.
1. Press the button 1 second to preview default setting value.
2. Press to exit preview default mode or wait for 3 second for automatically.
Press the button 2 second to
enter the set up mode and change
default. For jump to next setting,
press after finishing. To exit, press
or wait for 10 second.
SPO2 mode
To setup Max SpO2 rate, press
to enter, and it shows as
picture and press / button
for adjustment. To set up Min SpO2
rate, press , and it shows
as picture and same as max setting.
Pulse Rate mode
To setup Max Pulse rate, press
to enter, and it shows as
picture and press / button
for adjustment. To set up Min Pulse
rate, press , and it shows
as picture and same as max setting.
Memory interval mode
1. Optional of SA120: 5 / 10 / 30 / 60
minutes.
2. While the memory mode, the
memory interval mode
appears on the screen. To
change the default, press /
to change (5)-(10)-(30)-(60) or
(60)-(30)-(10)-(5) minutes.
Sound volume control
For the control of sound volume,
for loud volume, for lower
volume. To change the sounds
volume, Press / to change
--> .
Time Setup
To set up the time, it starts from
year as picture, and press /
to adjust. Following the same
frequency for month, date, hour
to minutes.
Warning: Press or wait for 10 seconds to exit, the setup value will be reserved.
Please double-check the set value before use.
Name/ Functions of each part
Pulse Oximeter
2
4
3
1
10
11
12
9
8
6
7
5
No. Item Purpose
1Pulse strength
2Probe icon
3LCD backlight button For light on/ o
4Sound button
For Heartbeat sound
loud volume
lower volume
silence
5 Time Shows the time
6SpO2 icon High SpO2
Low SpO2
7Pulse Rate High Pulse Rate
Low Pulse Rate
8UP/DOWN button For adjust/view all setting/ memory
memory icon
9Set button For view/ adjust default setting
10 Alert button Alert o / Alert pause
11 Power button Power on/ o
12 Battery compartment
For install or replace batteries
Full batteries
out of batteries
SA120 All symbols
SA120 All symbols
SA120 All symbols
SA120 All symbols
SA120 All symbols
SA120 All symbols
SA120 All symbols
SA120 All symbols
SA120 All symbols
1
second
2 seconds
High SpO2
Low SpO2
100
99
98
97
.
.
90
88
86
84
82
.
.
SA120 All symbols
SA120 All symbols
SA120 All symbols
SA120 All symbols
High
Pulse Rate
Low
Pulse Rate
140
135
130
125
55
50
45
40
35
SA120 All symbols
Memories reading and delete
Enter the memory mode with the or to read the SpO2 and pulse rate in
memory mode.
Note: When entering the memory reading mode, the will appear on the
screen.
SA120 All symbols
SA120 All symbols
SA120 All symbols
2
seconds
2 seconds to
clean data
Press for two second during the memory reading mode, it will enter the
memory delete mode. The screen show and means not to delete any
data, while the screen with and , it means to delete data.
Caution: The deleted data could not be restored.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rossmax SA120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rossmax SA120 in the language / languages: English as an attachment in your email.

The manual is 5.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info