803562
14
Zoom out
Zoom in
Previous page
1/36
Next page
EN
Key functions
MODE: press it to select functions. Hold it for
3 seconds to reset time, distance and calories.
OPERATUION PROCEDURES:
AUTO ON/OFF:
The system turns on when any key is pressed
or when it receives an signal input from the
speed sensor.
The system turns o automatically when
the sensor has no signal input or no key are
pressed for approximately 4 minutes.
RESET: The unit can be reset by either chan-
ging the battery or pressing the mode key for
3 seconds.
MODE: To choose the SCAN or LOCK if you do
not want the scan mode, press the MODE key
when the pointer on the function you want
which begins blinking.
FUNCTIONS:
SCAN: Display changes according to the next
diagram every 4 seconds. TIME - SPEED - DIS-
TANCE - CALORIE - ODOMETER - PULSE
TIME: Press the MODE key until pointer lock
in to TIME. The total working time will be
shown when starting exercise.
SPEED: Press the MODE key until pointer lock
on to SPEED. Display current speed during
working time.
DISTANCE: Press the MODE key until pointer
lock on to DISTANCE. The distance of each
workout will be displayed when starting
exercise.
CALORIE: Press the MODE key until pointer
lock on to CALORIE. The calorie burned will
be displayed when starting exercise.
ODOMETER: Press the MODE key until pointer
lock on to ODO (Total distance) Automatically
accumulates workout distance when starting
exercise.
PULSE: Please press the MODE key until poin-
ter lock on to the” PULSE” function. Through
the heart rate sensor, measuring the number
of beats per minute.
Battery
This monitor uses two type AA batteries. If
improper display on monitor, please reinstall
the batteries to have a good result.
Maintenance
Verify that all the bolts and nuts are locked
properly and the turning parts should be
turned freely without damaged parts.
Clean the equipment with soap and slightly
damp cloth only. Please do not use any sol-
vent to clean the equipment.
Malfunctions and treatment
Base is unstable. Floor is not at or there is
small object under the front or rear stabilizer.
Remove the object. The rear stabilizer end
caps have not been leveled when assem-
bling. Adjust the rear stabilizer end caps.
Handlebar or seat cushion is shaking. Tighten
the bolts and saddle post knob.
Loud noise from the moving parts. The
interval of the parts is improperly tightened.
Open the covers to adjust.
No resistance while using the equipment.
The interval of the magnetic resistance
increases. Open the covers to adjust.
Tension control is damaged. Change the
tension control.
Running belt slips. Open the covers to adjust.
The bearing set is damaged. Change the
bearing set.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rossler 021092 Cluster crosstrainer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rossler 021092 Cluster crosstrainer in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 4.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info