761245
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
ENGLISH
Power Supply
Insert the supplied power cord into the power cord connector
of the continuous light.
Press the on/off switch to position „I“ to switch on the LED
light. In position „O“, the light is switched off.
Compatibility of Accessories
The LED permanent light is equipped with an umbrella holder
for reflex/transmitted light umbrellas and the Bowens S-type
mount for the use of various light shapers (softboxes, reflectors,
beauty dishes, etc.).
Insert the light shaper with the three bayonet pins into the
corresponding recesses on the LED lighting head and lock it by
turning it briefly to the right until it audibly clicks into place.
To remove the light shaper, pull the mount release button to
the rear, turn the light shaper to the left and pull it off to the
front.
U-bracket
To enable the LED light
to also be mounted from
above (e.g. on the ceiling),
the unit is attached using
the useful U bracket. You
can loosen the knobs on
the sides, turn the bracket
around and mount it again
from above. This ensures
that the heat is still reliably
dissipated.
Brightness
After power on, turn the adjustment knob clockwise to increase
the brightness and counterclockwise to decrease the brightness.
The brightness can be adjusted between 0% and 100% in 1%
increments.
Lighting Effects
You can use the LED permanent light to create various lighting
effects. To do this, briefly press the light effect mode button to
access the effects. By briefly pressing the light effect mode button
again, you can now choose between the different modes:
1: TV flicker
2: Flickering light bulb
3: Fireworks
4: Thunderstorm mode
5: Flashing mode
After selecting the desired lighting effect, briefly press the adjust-
ment knob to set the effect. Press once to access the brightness
setting, press again to access the frequency setting. By turning the
setting knob at a time, you can adjust the brightness between
0 – 100% and the frequency between 1 – 10. 1 describes the slo-
west and 10 the fastest frequency.
Modes 1 and 2 run continuously, modes 3, 4 and 5 play short
light sequences. To start them, briefly press the lighting effect
start button.
To switch off the lighting effects, press the return button.
Settings Menu
Press the Menu key to display the Settings menu.
Briefly press the setting button to scroll through the options.
When an option is selected, the icon turns green. Turn the set-
ting knob to select the setting, confirm by briefly pressing the
setting knob and press the return key to return to the menu.
The settings menu contains the following options:
Fan: Auto / On / Off
Communication: Radio
signal over 2.4 GHz /
Bluetooth* / DMX
Reset Bluetooth*:
Yes / No
Factory settings:
Yes / No
Cooling
You can switch the cooling system of the LED light on or off.
To do this, go to the settings menu and switch off the cooling
system via the first setting point. The symbol in the display
indicates whether the cooling system is switched on or off.
Please note that when the cooling system is switched off, the
LED light can only be operated at a maximum output of 30% to
protect it from overheating. This reduced power is nevertheless
indicated as 100% power.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rollei Soluna 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rollei Soluna 300 in the language / languages: English, German as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info