647722
106
Zoom out
Zoom in
Previous page
1/169
Next page
106
Installing a Wave Expansion Board
Two Wave Expansion Boards (SRX series; sold separately) can be
installed in the XV-2020.
Waveform data, patches and rhythm sets are stored on the Wave
Expansion Board, so you can increase the number of available
sounds by installing the board in the XV-2020.
Installing a Wave Expansion Board increases the patches and drum
sets for Parts, but the number of Parts doesn’t change.
The Wave Expansion Board can be installed by removing the top
cover.
Cautions When Installing an
Wave Expansion Board
To avoid the risk of damage to internal components that can be
caused by static electricity, please carefully observe the
following whenever you handle the board.
Before you touch the board, always first grasp a metal object
(such as a water pipe), so you are sure that any static
electricity you might have been carrying has been
discharged.
When handling the board, grasp it only by its edges. Avoid
touching any of the electronic components or connectors.
Save the bag in which the board was originally shipped, and
put the board back into it whenever you need to store or
transport it.
Do not touch any of the printed circuit pathways or connection
terminals.
Never use excessive force when installing a circuit board. If it
doesn’t fit properly on the first attempt, remove the board and
try again.
When circuit board installation is complete, double-check your
work.
Install only the specified board, and remove only the specified
screws.
Be careful not to cut your hands on the opening for installing
the board.
Expansion Board
1. Before installing the Wave Expansion Board, switch off the
power to the XV-2020 and any connected equipment.
2. Detach the cover on the upper portion of the XV-2020.
Loosen the screw on the upper portion of the cover.
fig.1-03a.e
3. Position the board holders so they are oriented.
fig.Install2.e
4. Insert the connector for the Wave Expansion Board into the
connector on the unit, and at the same time, fit the board
holders into the holes.
fig.Install3.e
5. Use the tool supplied with the Wave Expansion Board to
rotate the board holders to LOCK, securing the Wave
Expansion Board in place.
fig.Install4
6. Use the (specified) screws you removed in step 2 to
reattach the cover.
This completes the installation of the Wave Expansion Board.
Next, make sure the board is installed correctly.
Driver
Holder
Holder
Connector
LOCK
106


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland XV-2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland XV-2020 in the language / languages: English as an attachment in your email.

The manual is 4,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info