Manual Roland XV-2020 (page 50 of 169) (English)

647722

Zoom out

Zoom in

1/169

Creating a Patch

MATRIX CTRL (Patch Matrix Control)

This selects the parameters to be controlled by Matrix Control Source 1–4 and the Sens settings, as well as

the specific Tones whose parameters you wish to control. Up to four destination parameters can be

selected for each controller and controlled simultaneously.

* Parameters that can be set independently for each Tone are indicated by “#.”

PATCH CONTROL SWITCH

These settings determine each Tone’s response to received Pitch Bend, Expression, Pan, Hold1, Damper,

and Envelope Mode MIDI messages.

* Parameters that can be set independently for each Tone are indicated by “#.”

Parameter Value Description

SOURCE1–4

(Matrix Control

Source1–4)

OFF, CC01–31, CC33–95, BEND, AF-

TER, SYS1–4, VELOCITY,

KEYFOLLOW, TEMPO, LFO1, LFO2,

PIT-ENV, TVF-ENV, TVA-ENV

Assign one of the following controllers to Control Source 1–4. If you wish

to use a controller that will apply to all Patches, or a controller that cannot

be directly selected here, select SYS-CTRL1–4, and then select the control-

ler using the Control Source 1–4 parameters (SYSTEM COMMON).

DESTINATION1–4

(Matrix Control

Destination 1–4)

OFF, PITCH, CUTOFF, RESONANCE

LEV,EL PAN, DRY LEVEL, CHORUS

SEND, REVERB SEND, LFO1/2 PCH

DEPTH, LFO1/2 TVF DEPTH, LFO1/

2 TVA DEPTH, LFO1 PAN DEPTH,

LFO1/2 RATE, PCH ENV A/D/R-

TIME, TVF ENV A/D/R-TIME, TVA

ENV A/D/R-TIME, TMT, FXM

DEPTH, MFX-CTRL1/4

Selects a parameter to be controlled.

SENS1–4

(Matrix Control

Sens 1–4)

-63–+63 Adjusts the amount of change that occurs in response to controller chang-

es. Negative (-) values invert the change. For LFO rates, negative (-) values

slow down the LFO, and positive (+) values speed it up.

TONE1–4#

(Matrix Control

Tone Control

Switch 1–4)

OFF, ON, REV Selects the Tone to which the two previous parameter settings are ap-

plied. “ON” turns signifies that the Tone is selected for control, “OFF”

that it’s not selected, and “REV (REVERSE)” that the change being ap-

plied is inverted when applied to this Tone.

Parameter Value Description

RCV BENDER#

(Tone Receive Bender Switch)

OFF, ON If you want the Tone to respond to Pitch Bend messages, turn this parameter

on. If not, turn it off.

RCV EXP#

(Tone Receive Expression Switch)

OFF, ON If you want the Tone to respond to Expression messages, turn this on. If not,

turn it off.

RCV HOLD-1#

(Tone Receive Hold 1 Switch)

OFF, ON Set this to ON if you wish the tone to respond to Hold1 messages—these mes-

sages cause sounds to continue playing when a sustain/damper pedal is

pressed. Set this to OFF when you don’t want the Tone to respond to Hold1

messages.

REDAMPER#

(Tone Redamper Switch)

OFF, ON If a Hold 1 message is received during the time between a note-off—when you

release the key—and the time at which the note actually disappears, any cur-

rently sounding notes will be sustained if Redamper is set to ON. To take ad-

vantage of this feature, you must also turn on the Tone Receive Hold 1 setting.

RCV PAN MODE#

(Tone Receive Pan Mode)

CONTINUOUS,

KEY-ON

CONTINUOUS: Pan messages are responded to immediately, instantly

changing the stereo position of the Tone.

KEY-ON: The stereo location of the Tone is changed only when the next note

is played. If a Pan message is received while a note is sounding, its stereo lo-

cation will not change.

ENV MODE#

(Tone Envelope Mode)

NO-SUS, SUSTAIN When a loop-type waveform is selected, it normally continues to sound as

long as a key is pressed. If you want a note to decay naturally even when the

key remains pressed, set this to “NO-SUS.”

* If a one-shot type Wave is selected, it will not sustain even if this parameter is set

to “SUSTAIN.”

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Roland XV-2020 in the language / languages: English as an attachment in your email.

The manual is 4,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Roland XV-2020 Manual

Product: