647744
16
Zoom out
Zoom in
Previous page
1/216
Next page
16
Getting Ready
Installing the Wave Expansion Board
Up to two Wave Expansion Boards (SR-JV80 series; sold separately) can be
installed in EXP-D and E Slots in the XP-30. Wave Expansion Boards contain
Wave data, as well as Patches and Rhythm Sets that use this Wave data,
which can be called directly into the temporary area and played.
Cautions When Installing an Wave Expansion Board
To avoid the risk of damage to internal components that can be caused by
static electricity, please carefully observe the following whenever you
handle the board.
Before you touch the board, always first grasp a metal object (such as
a water pipe), so you are sure that any static electricity you might
have been carrying has been discharged.
When handling the board, grasp it only by its edges. Avoid touching
any of the electronic components or connectors.
Save the bag in which the board was originally shipped, and put the
board back into it whenever you need to store or transport it.
Use a Philips screwdriver that is suitable for the size of the screw (a
number 2 screwdriver). If an unsuitable screwdriver is used, the head of
the screw may be stripped.
To remove a screw, rotate the screwdriver
counter-clockwise. To tighten a screw, rotate
the screwdriver clockwise.
When installing Wave Expansion Boards,
remove only the specified screws.
Be careful that the screws you remove do not drop into the interior of the
XP-30.
Do not leave the bottom cover in a detached state. Be sure to reattach it
after the Wave Expansion Boards have been installed.
Do not touch any of the printed circuit pathways or connection terminals.
Be careful not to cut your hand on the edge of the installation bay.
Never use excessive force when installing a circuit board. If it doesnt fit
properly on the first attempt, remove the board and try again.
When circuit board installation is complete, double-check your work.
To install an optional Wave Expansion Board (SR-JV80 series; sold
separately), the units bottom cover must be removed. There are two slots
(EXP-D and E) into which a board can be installed. Slots EXP-D and E
correspond to the group (XP-D and E) you need to select in order to use a
Wave, Patch or Rhythm Set from the Wave Expansion Board.
When playing a Patch or
Rhythm Set that use the
Wave data from a Wave
Expansion Board, the
appropriate Wave
Expansion Board must be
installed in the XP-30 for
the sound to play correctly.
tightenloosen
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland XP-30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland XP-30 in the language / languages: English as an attachment in your email.

The manual is 5,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info