481047
18
Zoom out
Zoom in
Previous page
1/32
Next page
GX-24 – Uitvoeren van snijopdrachten
18
Wacht tot de operatie beëindigd is en ga dan na of ma-
teriaal nog degelijk vastzit.
GOED
FOUT
DGa na of het materiaal naar behoren doorgevoerd
wordt en druk op [MENU].
In het display moeten nu de hieronder getoonde waar-
den staan.
Details over de betekenis van de afgebeelde waarden
vindt u in de elektronische handleiding “GX-24 Refe-
rence Guide”.
Het materiaal is nu naar behoren geladen. Vervolg met
“Stap 2: Mesje installeren” (blz. 18).
Als het materiaal los komt
Als het materiaal onder de aandrukrollen wegschuift,
moet u als volgt tewerk gaan en de hele procedure ver-
volgens vanaf stap 1 herhalen.
Zie “Stap 1: Materiaal laden” (blz. 16).
AHoud de netschakelaar minstens één seconde inge-
drukt.
Het apparaat wordt uitgeschakeld. Als het apparaat niet
uitgaat, moet u de aansluiting van de adapter verbre-
ken.
BLaat de laadhendel zakken en verwijder het materiaal.
Bij gebruik van lange materiaalvellen
Materiaal zoals het testmateriaal, dat voorgesneden is,
noem je een “materiaalvel”. Bij gebruik van normale
materiaalvellen moet u [PIECE] kiezen om te zorgen
dat de breedte en lengte worden afgebeeld. Als het ma-
teriaal echter langer is dan 1,6 meter, wordt de lengte
ook bij keuze van [PIECE] niet meer afgebeeld. Bij ge-
bruik van materiaal dat langer is dan 1,6 meter moet u
[ROLL] kiezen en er dan voor zorgen dat het materiaal
niet kan verschuiven.
Meer details hierover vindt u onder “Werken met ma-
teriaalrollen of lange vellen” (blz. 26).
Stap 2: Mesje installeren
VOORZICHTIG
Raak het mesje nooit met blote vingers aan.
Anders is de kans op verwondingen namelijk betrekke-
lijk groot.
Schuif het mesje in de cuttereenheid.
ADraai de kap van de cutter helemaal aan (tot u hem
niet meer verder kunt draaien).
BSteek de pin in.
Druk de pin zo ver tot u hem niet meer kunt zien.
CInstalleer het mes.
DDe meshoogte moet altijd in functie van het gebruikte
materiaal worden gekozen.
In dit voorbeeld moet de meshoogte voor het testmate-
riaal worden gekozen. Draai de kap naar links tot het
mes ±1mm uit de cuttereenheid steekt.
20cm/s
50 gf 0.250mm ∆A
Snijsnelheid
Mesdruk
Snijrichting
Mesverschuiving
Cuttereenheid
Kap
Pin
De pin moet met een
duidelijk hoorbare klik
tevoorschijn komen.
Kap
Mes
Punt
Zo ver drukken tot de
pin eruit springt.
0.1mm
Schaal
Losdraaien
Meshoogte
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland GX-24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland GX-24 in the language / languages: Dutch as an attachment in your email.

The manual is 2,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info