528905
49
Zoom out
Zoom in
Previous page
1/220
Next page
Octave
E-60/E-50 Music Workstation
r
49
Opgelet: Als u ook de via MIDI ontvangen nootcommando’s
wilt transponeren, moet u “TRANSPOSE RX (On/Off)” op
blz. 192 op “ON” zetten.
(4) Druk op de [EXIT]-knop om terug te gaan naar de
hoofdpagina.
Zolang het interval niet “0” luidt, licht de
[TRANSPOSE]-knop op om duidelijk te maken dat de
Transpose-functie actief is. Om de transpositie weer
uit te schakelen moet u op de [TRANSPOSE]-knop
(c.q. het gelijknamige veld) drukken en vervolgens op
de toets die aan het “0”-interval is toegewezen.
Het transpositie-interval wordt op de hoofdpagina
afgebeeld:
De “–1” slaat op een verhoging van een halve toon,
zodat u telkens een “B” hoort, wanneer u een “C”
speelt. Het betekent ook dat u i.p.v. de “A”, die u mis-
schien speelt, een “Ais” (of “Bes/si bemol”) hoort.
Global Transpose
Er is ook een “overkoepelende” transpositieparameter
die voor alle secties van de E-60/E-50 geldt. De waarde
ervan wordt bij het Transpose-interval (evenals de User
Program-transpositie) opgeteld tot u hem weer op “0”
zet of de E-60/E-50 uitschakelt.
(1) Druk op de [MENU]-knop.
Het display verandert in:
(2) Druk op het [TUNING]- en daarna op het
[MASTER¥TUNE]-veld.
(3) Stel de gewenste transpositie in met het [√≈ƒ]- of
[≈®]-veld.
Het instelbereik luidt –6~0~5 halve tonen. Deze
instelling geldt voor alle secties en alle User Pro-
grams.
Octave
De Octave-functie is nog zo’n nuttige parameter waar-
mee u de toonhoogte van de gekozen part in octaaf-
stappen (12 halve tonen) kunt veranderen.
U zou deze functie kunnen gebruiken voor solo’s waar u
met de UP1- en UP2-part dezelfde klank aanstuurt,
maar wel wilt dat de UP2-part een octaaf boven of
onder UP1 weerklinkt. Een andere zinnige toepassing
van deze parameter is het aansturen van de “bijgelui-
den” van bepaalde klanken.
Dit werkt waarschijnlijk alleen, wanneer u een Key-
board-part (MBS, LWR, UP2, UP1) gebruikt zonder het
klavier te splitten (blz. 47). Als u namelijk de SPLIT-
mode kiest, kunt u links alleen een beperkt aantal noten
spelen (tot aan het splitpunt). Voor de “herrie” moet u
de instelling “–3” kiezen. Dit betekent echter ook dat u
de “echte” noten helemaal rechts moet spelen, omdat
de volledige Part/Tone lager getransponeerd wordt.
Deze parameter komt tevens van pas, wanneer u
klanken van een Drum Set wilt aansturen, die niet
beschikbaar zijn zolang het klavier normaal staat
ingesteld. Onthoud verder dat het klavier 61 (E-50)
c.q. 76 toetsen (E-60) telt, terwijl talrijke Drum Sets
klanken voor alle 128 mogelijke MIDI-noten bevatten.
EXIT
MENU
C2
C3
OCTAVE= 1
OCTAVE= 0
C2
C3
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland E-50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland E-50 in the language / languages: Dutch as an attachment in your email.

The manual is 12,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info