710397
10
Zoom out
Zoom in
Previous page
1/32
Next page
10
Panel Descriptions
1
DC IN jack
Connect the included AC adaptor here.
* Place the AC adaptor so the side with the indicator (see illustration)
faces upwards and the side with textual information faces downwards.
The indicator will light when you plug the AC adaptor into an AC outlet.
Power cord
AC Outlet
Indicator
* To prevent the inadvertent disruption of power to your unit (should the
plug be pulled out accidentally), and to avoid applying undue stress to
the jack, anchor the power cord using the cord hook, as shown in the
illustration.
2
[POWER] switch
This turns the power on/o.
* The power to this unit will be turned o automatically after a
predetermined amount of time has passed since it was last used for
playing music, or its buttons or controls were operated (Auto O
function).
If you do not want the power to be turned o automatically, disengage
the Auto O function.
For details on how to disable this function, refer to p. 22.
NOTE
5 Any settings that you are in the process of editing will be lost when
the power is turned o. If you have any settings that you want to
keep, you should save them beforehand.
5 To restore power, turn the power on again.
3
[MIC SENS] knob
Adjusts the mic input sensitivity.
4
MIC IN jack
Connect your microphone here.
You can use any one of three types of plugs (XLR, TRS, phone).
* Pin assignment of MIC IN jack
1: GND
2: HOT
3: COLD
GND (SLEEVE)
HOT
(TIP)
COLD (RING)
5
MASTER OUT 1 (L / R) connectors, 2 (L / R) jacks
Connect your powered speakers or power amp here.
* Pin assignment of MASTER OUT 1 connectors
6
BOOTH OUT (L / R) jacks
These are the output jacks for booth monitoring.
* Pin assignment of BOOTH OUT jacks
7
INPUT (CH 1–CH 4) jacks
These jacks input sound to channels 1–4. The CH1 and CH2 INPUT jacks
support phono input from MM-type cartridges.
Set the [INPUT SELECT] switch appropriately for the device you’re
connecting.
8
PHONO GROUND terminal
If a turntable (analog) is connected to the CH1 or CH2 INPUT jacks, connect
the turntable’s ground terminal here. This suppresses noise from the
turntable.
* Depending on the circumstances of a particular setup, you may
experience a discomforting sensation, or perceive that the surface feels
gritty to the touch when you touch this device, or the metal portions of
other objects. This is due to an innitesimal electrical charge, which is
absolutely harmless. However, if you are concerned about this, connect
the PHONO GROUND terminal with an external ground. When the unit
is grounded, a slight hum may occur, depending on the particulars of
your installation. If you are unsure of the connection method, contact
the nearest Roland Service Center, or an authorized Roland distributor,
as listed on the “Information page.
Unsuitable places for connection
5 Water pipes (may result in shock or electrocution)
5 Gas pipes (may result in re or explosion)
5 Telephone-line ground or lightning rod (may be dangerous in the
event of lightning)
9
MIDI OUT connector
This outputs MIDI messages such as MIDI clock.
10
USB HOST ports
These are USB audio input ports.
Both ports 3 and 4 can supply USB bus power.
* For more about devices that can be connected, refer to the Roland
website.
11
PC port
Use the included USB cable to connect this port to your computer.
To connect this to your computer, you must install the USB driver.
& “Installing the Software” (p. 3)
Computer
* Use the cord hook to secure the USB cable as shown in the illustration.
This prevents the plug from being pulled out, or strain from being
applied to the port.
To prevent malfunction and equipment failure, always turn down the volume, and turn o all the units before making any connections.
Rear Panel (Connecting Your Equipment)
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland DJ-808 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland DJ-808 in the language / languages: English as an attachment in your email.

The manual is 6,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland DJ-808

Roland DJ-808 User Manual - German - 32 pages

Roland DJ-808 User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info