527871

Roland D-2 GROOVEBOX Manual

82
Zoom out
Zoom in
Previous page
1/116
Next page
82
Troubleshooting
If the D2 stops producing sound, or if it does not function the way you expect, please check the following points first.
If checking these points does not resolve the problem, please contact your dealer or a nearby Roland service center.
* Roland can take no responsibility for the recovery of any lost data, or for any damages incurred as a result of such loss.
Problem Cause Action
No sound The D2 and/or connected equipment is not
powered-on.
Turn on the power.
Make sure that the AC adaptor is connected correctly.
The volume of the D2 and/or connected
equipment has been lowered.
Raise the volume.
MIDI cable(s) and/or audio cables are not
connected correctly.
Make the correct connections (p. 11).
The part level of the corresponding part is
lowered.
Raise the part level (p. 19).
Part R does not sound All rhythm tones are muted. Defeat muting of the rhythm tones (p. 17).
Sound is interrupted You are attempting to sound too many notes
at once (the maximum polyphony is 64
notes).
Reduce the number of notes that are played simultaneously.
Reduce the number of notes in the pattern that is playing back.
Some notes continue sound-
ing unnaturally.
The delay time, feedback, or amp envelope
release time settings are too high.
Lower these values (p. 43, p. 35).
Touching the D-FIELD does
not produce sound
A function that does not produce sound has
been assigned as the D-FIELD function.
Select a function that produce sound (such as RPS or ADLIB)
(pp. 23–32).
D-FIELD effect does not oc-
cur
You didn’t press the D-FIELD strongly
enough.
Press the D-FIELD with an appropriate amount of force.
The D2 is in SYSTEM/EDIT/WRITE modes. Press [EXIT] several times to exit these states.
The Sync Mode is set to “SLAVE.” Change the Sync Mode setting to “INT” (p. 74).
The sound continues even
after you remove your hand
from the D-FIELD.
[HOLD] is lit. Press [HOLD] to make it go dark.
Reverb/Delay/MFX is not
applied.
Reverb/Delay/MFX is turned “OFF.” Turn the desired effect “ON” (p. 42, p. 43, p. 44).
The Reverb Level or the Part Reverb Level
setting of each part is set to “0.”
Raise the value (p. 42, p. 19).
The Delay Level or the Part Delay Level set-
ting of each part is set to “0.”
Raise the value (p. 43, p. 19).
The MFX Output Level is set to “0.” The Part
MFX SW value of each part is set to “OFF.”
Raise the MFX Output Level. Turn the Part MFX SW “ON” (pp.
45–57, p. 19).
Pitch is incorrect. The tuning of the D2 or the external MIDI
sound source is incorrect.
Check the tuning setting (p. 73).
Patterns or songs will not
play back.
The D2 is in SYSTEM/EDIT/WRITE modes. Press [EXIT] several times to exit these states.
The Sync Mode setting is set to “SLAVE.” Chang the Sync Mode setting to “INT” (p. 74).
Pattern playback is not “on
the beat,” or lags.
The pattern contains too much data. Remove unwanted data. Use the Data Thin function to thin out
the data (p. 68).
Using the Move Note function, move note data that was input
as a chord (i.e., note data that is located at the same position)
backward in time (p. 64).
Use the Shift Clock function to move data of parts other than
the rhythm part backward in time (p. 68).
Tempo is too fast. Slow down the tempo (p. 16).
Can’t change patterns The CURRENT display is blinking when you
select a pattern.
Select a pattern when the CURRENT display is not blinking (p.
15).
The D2 is in Song mode or MEGAMIX mode. Press [PATTERN] to enter Pattern mode.
[ENTER] was not pressed. Press [ENTER] to finalize your selection.
The D2 does not operate cor-
rectly.
A panel button is being held down. Release the button.
… 82 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland D-2 GROOVEBOX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland D-2 GROOVEBOX in the language / languages: English as an attachment in your email.

The manual is 4,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland D-2 GROOVEBOX

Roland D-2 GROOVEBOX User Manual - German - 115 pages

Roland D-2 GROOVEBOX User Manual - Dutch - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info