527801
9
Zoom out
Zoom in
Previous page
1/12
Next page
9
KD-8
Adjusting the Foot Plate Height
Depending on your kick pedal, it can be unstable when you
attach it to the KD-8. Be sure to adjust the foot plate height so
that the entire bottom surface of the pedal is attached to the
floor.
1.
Loosen the stand’s anchor bolts and remove
the foot plate.
2.
Set the kick pedal so that the entire bottom
surface is attached to the floor.
3.
In most cases, the stand becomes somewhat
floated. Tighten the anchor bolts securely there
to fix the stand and foot plate.
Install the kick pedal securely.
Take care not to pinch your fingers.
The tips of the anchor bolts are sharp. Handle with care.
When moving the setup, be sure to remove the screws
and fold the stand. Transporting the KD-8 while it
remains open may subject the stand to excessive strain
and result in damage to the stand.
Adjusting the Anchor Bolts
When using the kick pedal on a carpet or similar surface, adjust
the anchor bolts so their tips protrude from the plate and secure
the pedal in place; this will make it easier to use the kick pedal.
However, when used on flooring, the anchor bolts may
damage the floor. Adjust the anchor bolts correctly.
The tips of the anchor bolts are sharp. Handle with care.
When Using a Twin Pedal
Position the two beaters equally
apart from the center of the pad as
shown in the figure at left. If one of
the beater is further away from the
center than the other, the sound from
the further beater will be lower in
volume, or will not sound as desired.
Using a twin pedal will result in
lower sensitivity as compared to
when a single pedal is used. Raise the
sensitivity on the sound module.
Commercially Available Kick Pedal
Beater
* Adjust the height so that the entire pedal comes
into contact with the floor.
This hight will vary depending
on your kick pedal.
When Using on the Carpet When using on the Floor
Adjusting the Anchor Bolts
PD/CY/KD/FD-8_e 9 ページ 2004年4月9日 金曜日 午前9時39分
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland CY-8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland CY-8 in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland CY-8

Roland CY-8 User Manual - German - 12 pages

Roland CY-8 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info