527390
78
Zoom out
Zoom in
Previous page
1/128
Next page
Menu options
78
r
Backing Module BK-7m
ative values reduce all velocity values by the same
amount (leaving differences between notes intact),
while positive settings increase all velocity values.
Cut Off
This filter parameter allows you to make the selected
sound darker or brighter. Positive settings mean that
more overtones are allowed to pass, so that the
sound becomes brighter. The further this value is set
in the negative direction, the fewer overtones will be
allowed to pass and the sound will become softer
(darker).
NOTE
For some sounds, positive (+) “Cut Off” settings will cause
no noticeable change because the preprogrammed “Cut
Off” parameter is already set to its maximum value.
Resonance
This is a parameter one invariably associates with a
synthesizer. When the “Resonance” value is increased,
the overtones in the area of the cutoff frequency will
be emphasized, creating a sound with a strong char-
acter.
NOTE
For some sounds, negative (–) “Resonance” settings may
produce no noticeable change because the resonance is
already set to the minimum value.
The following parameters allow you to set the
sound’s “envelope”. The envelope parameters affect
both the volume (TVA) and the filter (TVF). The cutoff
frequency will rise as the envelope rises and fall as
the envelope falls.
Attack (T)
This parameter adjusts the onset of the sound. Nega-
tive values speed up the attack, so that the sound
becomes more aggressive.
Decay (T)
This parameter adjusts the time over which the
sound’s volume and cutoff frequency fall from the
highest point of the attack down to the sustain level.
NOTE
Percussive sounds usually have a sustain level of “0”. Piano
and guitar sounds are in this category. Holding the keys for
a long time will have little effect on the duration of the
notes you are playing, even if you select a high value here.
Release (T)
This parameter adjusts the time over which the sound
will decay after the note is released until it is no
longer heard. The cutoff frequency will also fall
according to this setting.
NOTE
Some sounds already contain natural (sampled) vibrato
whose depth or speed cannot be changed.
Use the following three parameters if you think the
instrument in question has too much (or could use a
little more) vibrato.
Vibrato Rate (T)
This parameter adjusts the speed of the pitch modu-
lation. Positive (+) settings make the preset pitch
modulation faster, and negative (–) settings make it
slower.
Vibrato Depth (T)
This parameter adjusts the intensity of the pitch
modulation. Positive (+) settings mean that the
“wobble” becomes more prominent, while negative
(–) settings make it shallower.
Vibrato Delay (T)
This parameter adjusts the time required for the
vibrato effect to begin. Positive (+) settings increase
the time before vibrato will begin and negative set-
tings (–) shorten the time.
Parameter Setting
Velocity -127~+127
Parameter Setting
Cut Off -127~+127
Parameter Setting
Resonance -127~+127
Parameter Setting
Attack -127~+127
Characteristics of a low-pass filter
Cutoff frequency
Frequency
Setting
Parameter Setting
Decay -127~+127
Parameter Setting
Release -127~+127
Parameter Setting
Vibrato Rate -127~+127
Parameter Setting
Vibrato Depth -127~+127
Parameter Setting
Vibrato Delay -127~+127
BK-7m_UK.book Page 78 Tuesday, January 4, 2011 9:25 AM
78


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland BK-7M BACKING MODULE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland BK-7M BACKING MODULE in the language / languages: English as an attachment in your email.

The manual is 7,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland BK-7M BACKING MODULE

Roland BK-7M BACKING MODULE Additional guide - English - 10 pages

Roland BK-7M BACKING MODULE Additional guide - German - 10 pages

Roland BK-7M BACKING MODULE User Manual - German - 124 pages

Roland BK-7M BACKING MODULE User Manual - Dutch - 128 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info