527390

Roland BK-7M BACKING MODULE Manual

72
Zoom out
Zoom in
Previous page
1/128
Next page
Menu options
72
r
Backing Module BK-7m
To edit the SMF/Style Compressor parameters, use
[MENU] button ‰ “Mastering Tools” ‰ “SMF/Style Com-
pressor”.
1.
Select an SMF song or a Music Style and
start playback.
2.
Set the “Switch” parameter to “On” to acti-
vate the compressor.
The compressor is now active and will affect SMF
song or Music Style playback. (Select “Off” to switch
the compressor back off.)
3.
Use the [CURSOR÷VALUE] dial to select the
“Preset” parameter, then press the dial.
4.
Rotate the [CURSOR÷VALUE] dial to select
one of the available presets, then press the
dial.
The available presets are:
5.
If none of the preset memories contains the
settings you need, use the [CURSOR÷VALUE]
dial to select and set the following parame-
ters:
Parameter Setting Explanation
Level 0~127 Use this parameter to set
the compressor’s input level.
The higher the value, the
stronger the three frequency
bands are compressed.
The value you set here is
added to the “Level” settings
of the three bands. If you set
this parameter to “0”, the
compressor has no effect on
the output signal.
Gain –12~0~
12dB
Use this parameter to cor-
rect the level at the com-
pressor’s outputs. If the
settings of the remaining
parameters lead to a signifi-
cantly lower level, select a
positive value. If your set-
tings lead to a significantly
higher level, select a nega-
tive value. “0” means that
the level is neither boosted
nor attenuated.
High/Mid/Low: Because “Attack”, “Release”, “Threshold”,
“Ratio” and “Level” are the same for each band, we will
only discuss them once. As you see, each of the three fre-
quency ranges has its own set of parameters that allow
you to specify their behavior.
1. Hard Comp
2. Soft Comp
3. Low Boost
4. Mid Boost
5. High Boost
6. Standard
7. User
Attack 0~100ms Use this parameter to spec-
ify how fast the compressor
of the band in question
should start processing the
signal once the level of that
band exceeds the “Thresh-
old” level. Choose a smaller
value if you prefer a com-
pression similar to that of
FM radio stations. Higher
values may yield a “snap-
pier” or “funkier” sound.
Release 50~
5000ms
This parameter allows you to
specify how fast the com-
pressor of the corresponding
band should stop working
when the signal level drops
below the “Threshold” value.
Threshold –36~0dB This parameter allows you to
set the level the frequency
band (“High”, “Mid” or
“Low”) must reach to trigger
its compressor. The lower
the value, the more notice-
able the compression will be.
Ratio 1:1.0~
1:INF
Use this parameter to spec-
ify how strongly the level
should be reduced when the
band’s level exceeds the
“Threshold” level. “1:2.0”, for
example, means that level
values above the “Threshold”
level are halved. “1:INF” is
useful if you set “Threshold”
to “0dB” or thereabout. This
produces a limiter effect,
which means that no signal
level will ever exceed the
“Threshold” value. This may
help you protect the speak-
ers of the PA system etc.
Level –24~
+24dB
This parameter allows you to
establish the desired mix
among the three compressor
bands. Choose a negative
value to decrease the level,
or a positive one to increase
it. Choose “0” for a band
whose level is OK as is.
Split High 2000~
12000Hz
These two parameters spec-
ify the frequency where two
bands are separated. The
compressor has three bands,
and so there are two cross-
over frequencies you can
set: “High” between the
“Mid” and “High” ranges;
and “Low” between the
“Mid” and “Low” ranges.
Split Low 80~800Hz
Parameter Setting Explanation
BK-7m_UK.book Page 72 Tuesday, January 4, 2011 9:25 AM
… 72 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland BK-7M BACKING MODULE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland BK-7M BACKING MODULE in the language / languages: English as an attachment in your email.

The manual is 7,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland BK-7M BACKING MODULE

Roland BK-7M BACKING MODULE Additional guide - English - 10 pages

Roland BK-7M BACKING MODULE Additional guide - German - 10 pages

Roland BK-7M BACKING MODULE User Manual - German - 124 pages

Roland BK-7M BACKING MODULE User Manual - Dutch - 128 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info