527335
125
Zoom out
Zoom in
Previous page
1/148
Next page
123
Connecting with External Devices
Connecting with External Devices
Normally, you don’t need to install a driver in order to connect
the ATELIER to your computer. However, if some problem
occurs, or if the performance is poor, using the Roland
original driver may solve the problem.
Specify the USB driver you want to use, and then install the
driver.
1.
Press the [Utility] button.
2.
Press the Menu [ ] and [ ] buttons to
select “USB Driver.”
fig.10-12.eps
3.
Press the Value [-] and [+] buttons to select
“GENERIC” or “ORIGINAL.”
4.
Turn the ATELIER’s volume to the minimum
level, switch off the power, then turn it back on
again.
This setting remains stored in memory even while power is
turned off.
By connecting an external MIDI device and exchanging
performance data, you can control the performances on one
device from the other. For instance, you can output sound from
the other instrument or switch voice on the other instrument.
What’s MIDI?
MIDI, short for “Musical Instrument Digital Interface,” was
developed as a standard for the exchange of performance
data between electronic instruments and computers.
The ATELIER is equipped with MIDI connectors to let it
exchange performance data with external devices. These
connectors can be used to connect the ATELIER to an external
device for even greater versatility.
About MIDI Connectors
The ATELIER has two kinds of MIDI connectors.
Connecting these to the MIDI connectors on a MIDI instrument
makes it possible for the two instruments to control each other.
For instance, you can output sound from the other instrument
or switch tones on the other instrument.
You should also set the MIDI send channel as needed (p. 117).
fig.10-09.eps
MIDI Out Connector
Connect the external MIDI device to the MIDI IN connector
with an optional MIDI cable. The notes played on the
keyboard, movements of the Damper pedal, Expression data,
data indicating that a Registration button [1]–[8], etc., was
pressed will be transmitted to the external MIDI connector.
MIDI In Connector
Connect the external MIDI device to the MIDI out connector
with an optional MIDI cable. Performance messages from an
external MIDI device are received here.
These incoming messages may instruct the receiving MIDI
instrument to play sounds or switch voices.
The ATELIER contains two sound generators: one sound
generator for its own keyboards and one GM2/GS sound
generator (p. 133). Normally, musical data transmitted from
an external device to the MIDI In connector is sent to the
GM2/GS sound generator, but you can also set the “MIDI IN
Mode” parameter (p. 116) so that the keyboard sound
generator is controlled.
Making the Settings for the USB Driver
Setting
Descriptions
GENERIC
Choose this if you want to use the
standard USB driver that was included
with your computer.
Normally, you should use this mode.
ORIGINAL
Choose this if you want to use a USB
driver downloaded from the Roland
website.
Connecting MIDI Devices
AT-100-300_e.book 123 ページ 2008年5月7日 水曜日 午後3時33分
125


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland AT100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland AT100 in the language / languages: English as an attachment in your email.

The manual is 19,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland AT100

Roland AT100 User Manual - Dutch - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info