708884
23
Zoom out
Zoom in
Previous page
1/270
Next page
22
Before You Start Playing
Using a Microphone
The AT-80SL/60SL is equipped with a Mic jack.
Since this instrument has a Mic In jack, you can use a
microphone to enjoy a variety of possibilities such as singing
along with your performance, or singing along with SMF
music files (sold separately).
fig.00-32
1.
Connect your microphone to the [Mic In] jack
underneath the left side of the keyboard.
2.
Use the [Mic Volume] knob to adjust the volume
level for the microphone.
You can adjust the depth of the echo applied to sound from
the microphone (p. 194).
The microphone must be purchased separately. When
purchasing a microphone, please consult the vender where
you bought the AT-80SL/60SL.
NOTE
(AT-80SL only)
If the Input switch is set to “RSS,” RSS reverb will be applied
to the sound from the microphone. You can use the [Mic
Volume] knob to adjust the microphone volume (p. 210).
Some Notes on Using a Microphone
fig.00-31
To avoid disturbing others, be careful of the volume
level when playing late at night or very early in the
morning.
When connecting a microphone to the AT-80SL/60SL, be
sure to lower the volume. If the volume control is too
high when the microphone is plugged in, noise may be
produced by the speakers.
Howling could be produced depending on the location
of microphones relative to speakers. This can be
remedied by:
• Changing the orientation of the microphone.
• Relocating the microphone so it is farther from the
speakers.
• Lowering volume levels.
Turning On the Lights (AT-80SL)
After turning on the power, turn on the [Illumination] switch
(located underneath the left-hand side of the keyboard).
fig. 00-33
The panel illumination of the instrument will light.
Cautions When Using Illumination
fig.00-31
When the illumination is used for an extended period, the
light bulbs and the metal parts near the light bulb (see
diagram below) will become hot. Be careful not to touch
these areas. In particular, be careful of the following
locations.
1.
Panel illumination light bulb
Do not touch the light bulb or nearby parts. When
closing the lid, be sure to hold the handles.
2.
Metal fittings of the cover
After closing the lid, do not touch this area.
The bulbs used for illumination can be replaced. For details
on replacing a bulb, refer to
“Replacing the Illumination
Bulbs (AT-80SL Only)”
(p. 251).
fig.00-35
Illumination
On
1
2
Illumination Switch
AT-80SL_60SL_e.book 22 ページ 2004年3月23日 火曜日 午前9時34分
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland AT-60SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland AT-60SL in the language / languages: English as an attachment in your email.

The manual is 13,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland AT-60SL

Roland AT-60SL User Manual - German - 266 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info