Manual Roland AT 45 (page 6 of 228) (English)

527353

Zoom out

Zoom in

1/228

Important Notes

556

• When connecting / disconnecting all cables, grasp the

connector itself—never pull on the cable. This way you

will avoid causing shorts, or damage to the cable’s

internal elements.

557

•A small amount of heat will radiate from the unit during

normal operation.

558a

• To avoid disturbing your neighbors, try to keep the unit’s

volume at reasonable levels. You may prefer to use

headphones, so you do not need to be concerned about

those around you (especially when it is late at night).

559b

• When you need to transport the unit, pack it in shock-

absorbent material. Transporting the unit without doing

so can cause it to become scratched or damaged, and

could lead to malfunction.

560

• Do not apply undue force to the music rest while it is in

use.

562

• Use a cable from Roland to make the connection. If using

some other make of connection cable, please note the

following precautions.

• Some connection cables contain resistors. Do not use

cables that incorporate resistors for connecting to this

unit. The use of such cables can cause the sound level

to be extremely low, or impossible to hear. For infor-

mation on cable specifications, contact the manufac-

turer of the cable.

565

• Before opening or closing the keyboard lid, always make

sure that no pets or other small animals are located on top

of the instrument (in particular, they should be kept away

from the keyboard and its lid). Otherwise, due to the

structural design of this instrument, small pets or other

animals could end up getting trapped inside it. If such a

situation is encountered, you must immediately switch off

the power and disconnect the power cord from the outlet.

You should then consult with the retailer from whom the

instrument was purchased, or contact the nearest Roland

Service Center.

Before Using Floppy Disks

Handling the Floppy Disk Drive

602

• Install the unit on a solid, level surface in an area free from

vibration.

603

• Avoid using the unit immediately after it has been moved

to a location with a level of humidity that is greatly

different than its former location. Rapid changes in the

environment can cause condensation to form inside the

drive, which will adversely affect the operation of the

drive and/or damage floppy disks. When the unit has

been moved, allow it to become accustomed to the new

environment (allow a few hours) before operating it.

604

• To insert a disk, push it gently but firmly into the drive—

it will click into place. To remove a disk, press the EJECT

button firmly. Do not use excessive force to remove a disk

which is lodged in the drive.

605a

• Never eject a disk while reading or writing is in progress,

since that can damage the magnetic surface of the disk,

rendering it unusable. (The disk drive’s indicator will

light up at full brightness when the drive is busy reading

or writing data. Ordinarily, the indicator will be less

brightly lit, or be extinguished.)

606

• Remove any disk from the drive before powering up or

down.

607

• To prevent damage to the disk drive’s heads, always try to

hold the floppy disk in a level position (not tilted in any

direction) while inserting it into the drive. Push it in

firmly, but gently. Never use excessive force.

608

• To avoid the risk of malfunction and/or damage, insert

only floppy disks into the disk drive. Never insert any

other type of disk. Avoid getting paper clips, coins, or any

other foreign objects inside the drive.

Handling Floppy Disks

651

• Floppy disks contain a plastic disk with a thin coating of

magnetic storage medium. Microscopic precision is

required to enable storage of large amounts of data on

such a small surface area. To preserve their integrity,

please observe the following when handling floppy disks:

• Never touch the magnetic medium inside the disk.

• Do not use or store floppy disks in dirty or dusty areas.

• Do not subject floppy disks to temperature extremes

(e.g., direct sunlight in an enclosed vehicle). Recom-

mended temperature range: 10 to 50° C (50 to 122° F).

• Do not expose floppy disks to strong magnetic fields,

such as those generated by loudspeakers.

652

• Floppy disks have a “write protect” tab which can protect

the disk from accidental erasure. It is recommended that

the tab be kept in the PROTECT position, and moved to

the WRITE position only when you wish to write new

data onto the disk.

653

• The identification label should be firmly affixed to the

disk. Should the label come loose while the disk is in the

drive, it may be difficult to remove the disk.

654

• Store all disks in a safe place to avoid damaging them, and

to protect them from dust, dirt, and other hazards. By

using a dirty or dust-ridden disk, you risk damaging the

disk, as well as causing the disk drive to malfunction.

655

• Disks containing performance data for this unit should

always be locked (have their write protect tab slid to the

“Protect” position) before you insert them into the drive

on some other unit (except the PR-300, or a product in the

HP-G, MT, KR, or Atelier families), or into a computer’s

drive. Otherwise (if the write protect tab remains in the

“Write” position), when you perform any disk operations

using the other device’s disk drive (such as checking the

contents of the disk, or loading data), you risk rendering

the disk unreadable by this unit’s disk drive.

* GS ( ) is a registered trademark of Roland Corpo-

ration.

203

* XG lite ( ) is a registered trademark of Yamaha Corpo-

ration.

220

* All product names mentioned in this document are trade-

marks or registered trademarks of their respective owners.

Rear side of the disk

Write

(can write new data onto disk)

Protect

(prevents writing to disk)

Write Protect Tab

AT-45_e.book 6 ページ２００５年２月２１日　月曜日　午後５時４３分

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Roland AT 45 in the language / languages: English as an attachment in your email.

The manual is 14,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland AT 45

Roland AT 45 User Manual - Dutch - 228 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Roland AT 45 Manual

Product: