481063

Roland AC-90 Manual

13
Zoom out
Zoom in
Previous page
1/80
Next page
Español Italiano Français Deutsch EnglishPortuguêsNederlands
13
Names of Things and What They Do
the MUTE button.
If devices are connected to both the RCA phono jacks and the
1/4” phone jacks, the two inputs are mixed.
4. DI OUT/TUNER OUT Jack
The direct sound of the device or instrument connected to the
GUITAR or MIC/LINE channel is output here. This is a 1/4”
phone TRS jack with balanced output.
You can also use this jack to connect a tuner.
fig.070
* If balanced output is not required, use a 1/4” phone (mono)
plug to connect to this jack.
If balanced output is not required, you can use the special
connection cable (the optional PCS-31) to use the DI OUT and
TUNER OUT simultaneously.
fig.080
A phase-inverted signal is output from the COLD side (the
red side of the PCS-31). Connect the recording device to the
HOT side (the white side of the PCS-31)
5. FOOT SW Jacks
The AC-90 accepts the BOSS FS-5L (latch type), BOSS FS-5U
(momentary type), and BOSS FS-6 foot switch pedals.
* Set the polarity switch as shown below.
fig.071
(MUTE, ANTI-FEEDBACK)
Connecting a foot switch pedal (optional BOSS FS-5L, FS-5U,
or FS-6) using a connection cable (the optional PCS-31) makes
it possible to use a latch-type foot switch (the FS-5L or FS-6)
to switch muting on and off, or to use a momentary-type foot
switch (the FS-5U or FS-6) to control the anti-feedback
feature.
* For information on the settings for the FS-6, refer to the
owner’s manual for the FS-6.
fig.050
When a 1/4” phone (mono) plug is used to connect only one
foot switch, only the Mute on/off function is enabled. In such
cases, you should use a latch-type foot switch pedal (such as
the BOSS FS-5L)
* The MUTE button should be set to off when a foot switch is
connected for muting.
You cannot switch the muting off by pressing the foot switch
when the MUTE button is on (when the MUTE indicator is
lit).
* When using an FS-5U (momentary type) to switch muting on
and off, the muting is switched on only while the switch is held
down.
For anti-feedback, a foot switch will function as follows:
• When the FREQUENCY knob is positioned in the range
from L to H, the switch turns the anti-feedback function
on and off.
• When the FREQUENCY knob is positioned at AUTO, the
switch functions as the START switch for the automatic
detection. Holding the foot switch down for one second
or longer returns the automatic detection function to
standby mode.
(CHORUS, DELAY/REVERB)
Using a special connection cable (the optional PCS-31) to
connect two foot switches (the optional BOSS FS-5U), you
can use one FS-5U to switch the chorus on and off, and use
the other FS-5U to switch the delay or reverb on and off.
fig.060
When a 1/4” phone (mono) plug is used to connect only one
foot switch, only the chorus on/off function is enabled.
* The chorus on/off function works on both channels.
* You cannot switch the chorus on and off by pressing the foot
switch when the CHORUS button is off.
Tuner
White Red
PCS-31
Recoreder
AC-90_egfispd.book Page 13 Tuesday, May 15, 2007 2:37 PM
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland AC-90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland AC-90 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 11,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info