481050
38
Zoom out
Zoom in
Previous page
1/96
Next page
38
Using A-PRO Editor
System Ex.
Assign a system exclusive message (System Ex.).
You can enter up to twenty-four bytes.
fig.editor-sysex.eps
Specify the following parameters.
Table 1: Special characters used in the message entry field
Table 2: Types of data you can specify in the Data Type field
Item Content
Message entry field
You can enter a system exclusive message of up to twenty-four bytes.
Enter each byte as a hexadecimal value separated by a single-byte space.
The following limitations apply to the input.
* The message must begin with “F0” and end with “F7.”
* You cannot include more than one exclusive message.
* You cannot include messages other than an exclusive message.
You can enter variable data or a checksum using the special characters
described in “Table 1: Special characters used in the message entry field”
(p. 38). If you use the special character “DT,” use the Data Type field to
specify the type of data.
Data Type
If you’ve used the special character “DT” in the message entry field, use
this to specify the type of data to be inserted at that location. For the
types of data that can be specified, refer to “Table 2: Types of data you
can specify in the Data Type field” (p. 38).
Min Value Lower limit of the data value
Max Value Upper limit of the data value
Special
character
Explanation Details
DT Data insertion location The data specified by Data Type will be inserted.
SS
Beginning of checksum
calculation
If you use the automatic checksum calculation function, use
this special character to specify the point at which check-
sum calculation is to begin.
S1/S2
Checksum insertion
location and type
If you use the automatic checksum calculation function, use
this special character to specify the point at which the
checksum is to be inserted, and its type.
S1: The most common type, used by Roland and other man-
ufacturers.
S2: Choose this if a method other than S1 is used.
?n
Channel (? is any value
between 0–7)
If you want a channel number to be inserted in the exclusive
message, use this special character to specify its location
and the upper four bits (a fixed value of 0–7). The current
channel of the A-PRO will be inserted in the channel section.
?x
Block number (? is any
value between 0–7)
If you want a GS block number to be inserted in the exclu-
sive message, use this special character to specify its loca-
tion and the upper four bits (a fixed value of 0–7). The
current channel of the A-PRO will converted into the block
number and inserted.
Data type Data length Target of the specified Min Value / Max Value
DT0: 7-bit 1 byte Specifies a range from 0 to 127 (0–127)
DT1: 4-bit/4-bit 2 bytes
Specifies the range of the first byte (0–15)
* The second byte is fixed at 0–15
DT2: 7-bit/7-bit
(MSB/LSB)
2 bytes
Specifies the range of the MSB (0–127)
* The LSB is fixed at 0–127
DT3: 7-bit/7-bit
(LSB/MSB)
2 bytes
Specifies the range of the MSB (0–127)
* The LSB is fixed at 0–127
DT4: 4-bit/
4-bit/4-bit/4-bit
4 bytes
Specifies the range of change (0–255) between the negative di-
rection (Min) and the positive direction (Max), centered on 8000h.
Example of input
1. Enter the following in the message entry field.
F0 41 10 42 12 SS 40 1X 32 DT S1 F7
2.
In the Data Type field, choose “DT0.” Specify the
Min Value as “0” and the Max Value as “127.”
F0 41 10 42 12 SS 40 1x 32 DATA SUM F7
Block number 1 byte
Address Data
ChecksumChecksum calculation range
A-300_500_800C_e.book 38 ページ 2014年8月19日 火曜日 午後3時27分
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland A-800PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland A-800PRO in the language / languages: English as an attachment in your email.

The manual is 15,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland A-800PRO

Roland A-800PRO User Manual - German - 96 pages

Roland A-800PRO User Manual - Dutch - 92 pages

Roland A-800PRO User Manual - French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info