168044

Rodek ri 450 200 Manual

19
Zoom out
Zoom in
Previous page
1/28
Next page
19
Make sure there is no wiring harness, fuel tank etc. behind or
below the mounting surface that may be damaged by the dril-
ling of the holes for the amplifier mounting screws. The above
mentioned clearance of at least 5cm to all sides of the amplifier
is not only for proper cooling, but also because the crossover
controls must remain accessible.
The amplifier must NOT be mounted directly to the chas-
sis ground of the vehicle, this may cause ground loops
resulting in loud hum noise.
3.2 MINIMUM IMPEDANCE LOAD
The output stages of the RODEK RI-450-200 multi channel am-
plifier are designed to give you high output power into 4 or 2
ohms loads in normal stereo configurations. In bridged mode,
the minimum impedance load is 4 ohms for the channels CH1/
CH2 and CH3/CH4. The amplifier might suffer from thermal
shut-down or even damage, if these recommended minimum
impedance load ratings are not considered appropriately.
3. MOUNTING OF THE AMPLIFIER
19
Before you attempt the installation of your RI-450-200 5-channel
amplifier, it is recommended to map out the complete audio
system and the respective wiring required. Please note that
– because of possible interference problems with the existing
car electrics and electronics – especially the routing of the
signal cables and the chassis ground connection will have a
profound impact on the performance of the overall system.
Secondly, the correct mounting location needs your attention
too (proper cooling of the amp!). Use only quality installation
material and if you have only little or no experience with complex
car audio installations, we strongly recommend you to consult
your nearest authorized RODEK dealer/installer.
3.1 MOUNTING LOCATION
The mounting location should be carefully selected, preferably
in the trunk compartment of your car! In the interest of passive
driver and passenger safety, the amplifier must be securely
mounted, and special precautions must be taken to allow suf-
ficient cooling. The amp can get quite hot during operation, so
a clearance of at least 10cm from both sides and from the top
of the amp must be considered.
Furthermore, this amplifier features an internal fan, so the side
panels must not be covered to allow for a good air flow in and
out of the side-panel windows.
RI-Amp 5-CH Manual_D+E.indd 19 05.01.2008 12:45:33 Uhr
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rodek ri 450 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rodek ri 450 200 in the language / languages: English, German as an attachment in your email.

The manual is 3,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info