167812
22
Zoom out
Zoom in
Previous page
1/28
Next page
22
4. ELECTRICAL wIRING
22
4. ELECTRICAL WIRING
IMPORTANT! Disconnect the positive battery ter-
minal (+12V) or remove the main fuse near the car
battery before you start any wiring work!
The power supply of the car audio system must be
disconnected until the entire wiring installation is
completed.
Use rubber grommets when running cables through any me-
tal or sharp plastic panels, to prevent accidental shorting or
shearing. Make sure the cables do not interfere with normal
operation of the vehicle.
Especially the music signal cables (RCA interconnects) should
be kept far away from any potential sources of electrical inter-
ference e.g. electronic vehicle management systems (engine
computers, relays etc.) fuel pumps, wiring harnesses etc.!
4.1 RCA INTERCONNECTS / REMOTE
LEAD
Carefully run the RCA audio signal interconnect(s) and the
remote switching cable from the head-unit to the amplifier.
The audio signal cables should be routed completely separate
from the power cables. Use only double or triple shielded quality
cables!
Connect the remote wire lead to the remote output of the head-
unit and to the remote input terminal of the amplifier. Finally
connect the RCA interconnect cable(s) to the respective out-puts
on the head-unit and the RCA inputs of the amplifier.
4.2 LOUDSPEAKER CABLES
Connect the loudspeaker wires to the speaker terminals of the
amplifier. Use good quality wires of 2.5mm² cross-section.
When baring wires, remove approximately 6-8mm of the insu-
lation and after axially twisting the wires; insert the bare ends
into the corresponding speaker terminal output on the amplifier.
Be sure to follow correct polarity ("+" to "+"; "-" to "-"). Tighten
the terminal screws on the amplifier.
4.3 CONNECTION OF POWER CABLES
Run the positive power cable ("+12 V") directly from the positive
terminal of the car battery to the amplifier. Make sure the power
cable makes good contact to the battery; i.e. use an approp-
riate battery clamp that accepts big gauge power cables! For
protection of your car audio system and your entire car against
electrical fire hazards from a short-circuit of the main power
cable with chassis ground, you must insert a main fuse (holder)
within the first 30cm of the battery. The fuse type/value should
be matching the limitations of your main power cable and the
requirements of your car audio system. For example 80 A fuse
when using 35mm² power cable.
Now you route the ground cable to the amplifier. It is best to
keep the ground cable ("-12V") as short as possible, i.e. to find
a chassis contact very close to the amplifier. The ground power
cable must have the same cross-section as the positive power
cable. It is recommended to use a corrosion-resistant gold-pla-
ted power ring or a massive ground clamp between the ground
cable and the chassis ground point. Keep in mind that audible
interferences and problems originating in the power supply of
the amplifier, are mostly based on a bad ground contact. So a
good (and clean) grounding to the vehicle chassis is absolutely
crucial, to obtain best performance of your amplifier.
Ro 6-CH Manual_D+E.indd 22 27.02.2006 18:15:45 Uhr
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rodek r 680 n at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rodek r 680 n in the language / languages: English, German as an attachment in your email.

The manual is 2,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info