167807
9
Zoom out
Zoom in
Previous page
1/32
Next page
9
Bevor Sie mit der Montage beginnen, erstellen Sie am besten
eine kurze Anschluss- und Installationsskizze. Beachten Sie
bitte, dass die Kabelführung und der gewählte Massepunkt
entscheidenden Einfluss auf das störungsfreie Funktionieren
Ihrer Anlage hat.
Besondere Aufmerksamkeit verdient auch die korrekte Plat-
zierung des Verstärkers (ausreichende Luftzufuhr!), sowie
die Qualität des verwendeten Zubehörs zur fachgerechten
Installation (Stromkabel, Cinchkabel, Sicherungshalter, Ver-
teilerblöcke, etc).
3.1 WAHL DES EINBAUORTES
Der Montageort des Verstärker muss im Sinne einer guten Wär-
meabführung als auch r die weiteren Einstellarbeiten an der
Aktivweiche des Verstärkers entsprechend platziert werden.
Als Montageort eignet sich z.B. ein Platz im Kofferraum, an der
cksitzbank oder an einem Seitenteil, bzw. jeder andere Ort,
der eine saubere Installation ermöglicht.
Die Endstufe wird im Betrieb heiß, es sollte also einen Ab-
stand von mindestens 5 cm oberhalb und auf den Seiten des
Alu-Kühlkörpers geachtet werden. Der Luftein- und Auslass
(innenliegender Lüfter!) befindet sich in den Seitenabdeckungen.
Dort sollte genügend Luft zirkulieren können!
Vermeiden Sie Montageorte mit "unbekanntem Hintergrund". Es
nnten sich der Benzintank, hydraulische Bremsleitungen, Ka-
bel etc. dahinter verbergen! Achten Sie auch auf einen trocken,
gegen mechanische Einwirkungen geschützten Installationsort,
der auch nach der Endmontage noch für die Bedienung und
Einstellung (Trennfrequenz- und Eingangsempfindlichkeits-
Regelung) des Verstärkers gut zugänglich ist.
3. mONTAGE
R4100N
ON OFF
°
180 0
PHASE
POWER
PROTECT
HIGH PASS
LOW PASS
400HZ 40Hz
10Hz 400HZ
HP FULL
9V 0.2V
LEVEL BP
CH1/2
0.2V 9V
FULL
40Hz 400HZ 10Hz 400HZ
HP
CH3/4
BP
PHASE
LOW PASS HIGH PASS
LEVEL
CH4
CH3
CH2
CH1
Die Endstufe darf nicht mit der Kfz-Chassismasse in
Berührung kommen, sie muss also in jedem Fall isoliert
montiert werden.
3.2 MINIMALE LASTIMPEDANZ
Die RODEK Verstärker sind von der Auslegung der Endtransis-
toren-Sektion auf eine sehr hohe Ausgangsleistung im 4 und 2
Ohm stereo Betrieb ausgelegt, sie bieten hier eine gemessen
am Preis überdurchschnittliche Performance. Die RODEK
Verstärker können auf eine 4 Ohm Last gebrückt werden. Im
Stereobetrieb darf die minimale Abschlussimpedanz von 2 Ohm
pro Kanal auf keinen Fall unterschritten werden. Dasselbe gilt
auch r den Brückenmodus, wo 4 Ohm die minimal zulässige
Lastimpedanz darstellen! Die R1900N treibt Subwoofer bis auf
1 Ohm Gesamtlast.
Ro 1-2-4-CH Manual_D+E def.indd 9 01.03.2006 10:55:31 Uhr
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rodek r 2200 n at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rodek r 2200 n in the language / languages: English, German as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info