167805
25
Zoom out
Zoom in
Previous page
1/32
Next page
25
FRONT PANEL
R4100N
R4100N
R4100N
ON OFF
°
180 0
PHASE
POWER
PROTECT
HIGH PASS
LOW PASS
400HZ 40Hz
10Hz 400HZ
HP FULL
9V 0.2V
LEVEL BP
CH1/2
0.2V 9V
FULL
40Hz 400HZ 10Hz 400HZ
HP
CH3/4
BP
PHASE
LOW PASS HIGH PASS
LEVEL
CH4
CH3
CH2
CH1
REAR PANEL
R4100N
B C D E F G
H I J K L M N
Q R SO P
3. mOUNTING Of THE AmPLIfIER
The amplifier must NOT be mounted directly to the
chassis ground of the vehicle, this may cause to ground
loops with loud hum noise.
3.2 MINIMUM IMPEDANCE LOAD
The output stages of the RODEK amplifiers are designed to give
you extraordinary output power into 4 or 2 ohms loads in normal
stereo configurations. In bridged mode, the minimum impe-
dance load is 4 ohms. The amplifier might suffer from thermal
shut-down or even damage, if these recommended minimum
impedance load ratings are not considered appropriately. The
R1900N is stable into 1 ohm.
Before you attempt the installation of your RODEK amplifier,
it is recommended to map out the complete audio system and
the respective wiring required. Please note that - because of
possible interference problems with the existing car electrics
and electronics - especially the routing of the signal cables and
the chassis ground connection will have a profound impact on
the performance of the overall system. Secondly, the correct
mounting location needs your attention too (proper cooling
of the amp!). Use only quality installation material and if you
have only little or no experience with complex car audio instal-
lations, we strongly recommend you to consult your nearest
authorized RODEK dealer/installer.
3.1 MOUNTING LOCATION
The mounting location should be carefully selected, preferably
in the trunk compartment of your car! In the interest of passive
driver and passenger safety, the amplifier must be securely
mounted, and special precautions must be taken to allow suf-
ficient cooling. The amp can get quite hot during operation, so
a clearance of at least 5cm from both sides and from the top of
the amp must be considered.
Furthermore, the 2-/4-channel models feature an internal fan,
so the side panels must not be covered to allow for a good air
flow in and out of the side-panels windows.
Make sure there is no wiring harness, fuel tank etc. behind or
below the mounting surface that may be damaged by the dril-
ling of the holes for the amplifier mounting screws. The above
mentioned clearance of at least 5cm
to all sides of the amplifier
is not only for proper cooling, but also because the crossover
controls must remain accessible.
Ro 1-2-4-CH Manual_D+E def.indd 25 01.03.2006 10:55:37 Uhr
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rodek r 1900 n at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rodek r 1900 n in the language / languages: English, German as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info