168822
5
Zoom out
Zoom in
Previous page
1/72
Next page
5
DESIGN FEATURES
INST
ALLATION
INSTALLATION CONSIDERATIONS
The following is a list of tools needed for installation:
Volt/Ohm Meter
Wire strippers
Wire crimpers
Wire cutters
#2 Phillips screwdriver
Battery post wrench
Hand held drill w/assorted bits
1/8" diameter heatshrink tubing
Assorted connectors
Adequate Length—Red 1/0 AWGPower Wire
Adequate Length—Remote Turn-on Wire
Adequate Length—Black 1/0 AWG Grounding Wire
11. RCA Input Jacks These pro-audio panel mount RCA jacks provide an easy connection for signal level
input.They are nickel-plated to resist the signal degradation caused by corrosion.Their design reduces the
stress created to internal boards when RCA cables are connected or disconnected.
12. Infrasonic Filter – A 28Hz High Pass filter designed to prevent frequencies below the audio range
from being applied to the subwoofer from the amplifier.Consequently improving subwoofer
performance and power handling, particularly in vented enclosures.
13. Gain Control The input gain control is preset to match the output of most source units. It can be
adjusted to match output levels from a variety of source units.
14. Variable Crossover – Is a built-in 24dB/octave Butterworth filter with a crossover point variable
from 35Hz to 250Hz.The crossover is set to Low-Pass (LP).
15. Mode Switch – Used to set the amplifier between single, for single amplifier use, and Master or Slave
for when connecting multiple bd amplifiers together.The first amplifier in the series being set as
Master and the subsequent amplifiers being set as Slave.This allows one gain, crossover, infrasonic
filter and bass boost setting for all slaved amplifiers.
NOTE: Gain on the Slave amplifier allows for fine tuning adjustment.
16. Phase Switch – Used when bridging two bd amplifiers together using a bd Sync cable to phase one
amplifier 180° from the other when driving a common load.
17. RCA Pass-Thru Jacks The Pass-Thru provides a convenient source for daisy-chaining an additional
amplifier without running an extra set of RCA cables from the front of the vehicle to the rear amplifier
location.
18. Remote Terminal This heavy duty, nickel-plated wire connector will accept wire sizes from
8 AWG to 16 AWG.This terminal is used to remotely turn-on and turn-off the amplifier when
+12V DC is applied.
19. Power Terminals The power and ground connectors on the amplifier are nickel-plated and will
accommodate up to 1/0 AWG wire maximizing the input current capability of the amplifier.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rockford Fosgate t2500 1bd at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rockford Fosgate t2500 1bd in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 5,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info