602251
11
Zoom out
Zoom in
Previous page
1/20
Next page
11
Troubleshooting
NOTE: If you are having problems after installation follow the Trouble-
shooting procedures below.
Step 1. Check Amplifier for proper connections. Verify that POWER light
is on. If POWER light is on skip to Step 3, if not continue.
1. Check in-line fuse on battery positive cable. Replace if necessary.
2. Check fuse(s) on amplifier. Replace if necessary.
3. Verify that Ground connection is connected to clean metal on the
vehicle’s chassis. Repair/replace if necessary.
4. Verify there is 9 to 14.4 Volts present at the positive battery and
remote turn-on cable. Verify quality connections for both cables at
amplifier, stereo, and battery/fuseholder. Repair/replace if necessary.
Step 2. Protect light is on.
1. If the Protect light is on, this is a sign of a possible short in the
speaker connections. Check for proper speaker connections and use
a volt/ohm meter to check for possible shorts in the speaker wiring.
Too low of a speaker impedance may also cause Protect to light.
Step 3. Check Amplifier for audio output.
1. Verify good RCA input connections at stereo and amplifier. Check
entire length of cables for kinks, splices, etc. Test RCA inputs for AC
volts with stereo on. Repair/replace if necessary.
2. Disconnect RCA input from amplifier. Connect RCA input from test
stereo directly to amplifier input.
Step 4. Check Amplifier if you experience Turn-on Pop.
1. Disconnect input signal to amplifier and turn amplifier on and off.
2. If the noise is eliminated, connect the REMOTE lead of amplifier to
source unit with a delay turn-on module.
OR
1. Use a different 12 Volt source for REMOTE lead of amplifier.
Step 5. Check Amplifier if you experience excess Engine Noise.
1. Route all signal carrying wires (RCA, Speaker cables) away from
power and ground wires.
OR
1. Bypass any and all electrical components between the stereo and the
amplifier(s). Connect stereo directly to input of amplifier. If noise goes
away the unit being bypassed is the cause of the noise.
OR
1. Remove existing ground wires for all electrical components. Reground
wires to different locations. Verify that grounding location is clean,
shiny metal free of paint, rust etc.
OR
1. Add secondary ground cable from negative battery terminal to the
chassis metal or engine block of vehicle.
OR
1. Have alternator and battery load tested by your mechanic. Verify good
working order of vehicle electrical system including distributor, spark
plugs, spark plug wires, voltage regulator etc.
Troubleshooting
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rockford Fosgate R250-1D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rockford Fosgate R250-1D in the language / languages: English as an attachment in your email.

The manual is 2,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info