65422

Rockford Fosgate Punch P4004 Manual

10
Zoom out
Zoom in
Previous page
1/64
Next page
10
ADJUSTING GAIN
Do the following individually for each channel.
To adjust the gain setting, turn the amplifier gains all the way down (counter-clockwise).Turn the source unit
volume up until distortion is audible and then turn it down a bit until the distortion is inaudible.This will be
about all the way up on most source units. Next,increase the amplifier gain setting until adequate volume is
achieved. Rockford Fosgate source units do not distort, so the volume can be used at maximum setting.
NOTE:Best signal to noise and dynamic range are realized with the gain at minimum. Most users find
adequate gain and volume is achieved at about halfway in the adjustment range.
CAUTION:Avoid setting the amplifier gain very high as noise and distortion will
increase significantly.
NOTE:For a more in depth setting procedure, contact Rockford Technical Support.
ADJUSTING CROSSOVER FREQUENCY
Placing the switch in the HP position sets the amplifier to the High Pass mode, enabling frequencies above
the cut-off point to pass, adjustable between 40-400Hz.
Placing the switch in the AP position sets the amplifier to the All Pass mode, preventing any crossover
adjustment, allowing all frequencies to pass.
Placing the switch in the LP position sets the
amplifier to the Low Pass mode, enabling
frequencies below the cut-off point to pass,
adjustable between 40-400Hz.
Turn the crossover adjustment knob all the
way down.With the system playing, turn the
crossover adjustment knob up slowly until
the desired crossover point is achieved.
Outside Panel Install
3. Using the screws supplied, install the
mounting clip.
4. Slip the remote onto the mounting
clip until it snaps into place.
5. Connect the cable to the remote.
Panel Install
6. Cut out a 2”x 7/8” hole in the panel,
with a maximum panel thickness of
3/8”. Ensure there is enough room
within the panel area for connection.
7. Route the cable through the hole and connect to
the remote.
8. Press the remote into the panel cutout until it clicks
in place.
Operation
9. Turn clockwise to add Punch to amplifier bass
frequencies.
CAUTION:Overexcursion and subsequent
damage may occur at high levels
of boost
NOTE:An optional Para-Punch Remote Bass is available
which adds an adjustable center frequency
control with the adjustable boost control.
Mounting Clip
OPERATION
Downloaded from www.Manualslib.com manuals search engine
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rockford Fosgate Punch P4004 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rockford Fosgate Punch P4004 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 4,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info