66479
4
Zoom out
Zoom in
Previous page
1/52
Next page
4578
9610
13 14
P400-2
11
12
4578
9610
13 14
P500-2
11
12
4578
9610
13 14
P200-2
P300-2
12
1. Power LED (Top of unit - Not Shown) This Blue LED illuminates when the unit is turned on.
2. Thermal LED (Top of unit - Not Shown) This Red LED illuminates if the amplifier internal
components become too hot and engage the thermal protection.The amplifier will shut down to cool
if this occurs.
3. Protect LED (Top of unit - Not Shown) This Yellow LED illuminates if a short circuit or too low of
an impedance is detected at the speaker connections.The amplifier will automatically shut down if this
occurs.
4. Cast Aluminum Heatsink The cast aluminum heatsink of the Punch amplifier dissipates heat
generated by the amplifier's circuitry.
5. Speaker Terminals The heavy duty,nickel-plated clamp wire connectors (
+
and -) will accept wire
sizes from 8 AWG to 18 AWG.
6. Remote Punch EQ (Optional Controller) The Remote Punch EQ connection is made with a RJ-45
cable and can be installed in a variety of ways for easy control access.The control is used to boost low
and/or high frequency information to overcome road noise.The remote overrides the Punch EQ on the
amplifier when connected.
NOTE:Previous (prior to 2007) Punch Bass and Para-Punch remotes will not work with these amplifiers.
7. Punch EQ A Gyrator based Punch EQ that eliminates frequency shift with boost.This works along
with the crossover switch on the amplifier.When set to Low-Pass (LP) operation,this is a variable Bass
Boost. When set to High-Pass (HP) operation,this is a variable Mid-Bass and Treble Boost. When set to
All Pass (AP) operation,both the Bass and Treble frequencies are boosted.
8. Crossover Switch – Selectable switch for High-Pass (HP),All Pass (AP),or Low-Pass (LP) operation.
9. Variable Crossover Is a built-in 12dB/octave Butterworth filter with a crossover point variable
from 50Hz to 500Hz.
10. Gain Control The input gain control is preset to match the output of most source units.It can be
adjusted to match output levels from a variety of source units.
11. RCA Pass-Thru Jacks (P400-2 and P500-2 only) This Pass-Thru provides a convenient source for
daisy-chaining an additional amplifier without running an extra set of RCA cables from the front of the
vehicle to the rear amplifier location.
4
DESIGN FEATURES
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rockford Fosgate Punch 200.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rockford Fosgate Punch 200.2 in the language / languages: English, German, French, Italian, Spanish, Spanish as an attachment in your email.

The manual is 2,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info