As the automotive manufacturers increasingly make their source units (radios) an integral part of the vehicle, it becomes increasingly harder to change
them out and upgrade your system. The 3Sixty.3 makes it possible to utilize the vehicle source unit and still create the sound experience that fits you. With
an easy to use interface, the 3Sixty.3 connected to your vehicle’s source unit and an amplifier, you can create a sound stage that is personally tuned to your
vehicle. The 3Sixty.3 gives you all the benefits of creating the best system possible without compromising the manufacturer’s integrated source system.
IMPORTANT To tune the 3Sixty.3 properly to your system the source unit must have a CD player, an amplifier with RCA inputs and a PC is also
required for initial setup and adjustments.
The following is a list of tools needed for installation:
This section focuses on some of the vehicle considerations for installing your new system.
Pre-planning your system layout and best wiring routes will save installation time. When deciding on the layout of your new system, be sure that each
component will be easily accessible for making adjustments.
If you feel unsure about installing this system yourself, have it installed by a qualified technician.
Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.
Before beginning any installation, follow these simple rules:
1. Be sure to carefully read and understand the instructions before attempting to install the unit.
2. For safety, disconnect the negative lead from the battery prior to beginning the installation.
3. For easier assembly, we suggest you run all wires prior to mounting your unit in place.
4. Route all of the RCA cables close together and away from any high current wires.
5. Use high quality connectors for a reliable installation and to minimize signal or power loss.
6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when
working on any vehicle.
7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.
8. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the
firewall.
9. ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power
wire within 18” (45.7 cm) of the battery terminal.
10. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections
should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.
Processor Mounting Locations
NOTE: The BT dongle signal will greatly be reduced if the unit is mounted under or behind any metallic material.
Engine Compartment
Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.
Trunk Mounting
The recommended orientation would be on the floor, as this would provide the best possible range for the Bluetooth controller. The device may be mounted
in any other orientation as long as Bluetooth range is maintained. Each vehicle is made of different materials and this may inhibit the Bluetooth range as
well. The less metal between the device and controller, the better the signal strength will be.
Passenger Compartment Mounting
This would be the ideal location for the device, as this would provide the optimal Bluetooth range.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Rockford Fosgate 3 SIXTY.3 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Rockford Fosgate 3 SIXTY.3 in the language / languages: English as an attachment in your email.
The manual is 6,77 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
