512484

Robomow Tuscania 500 Manual

86
Zoom out
Zoom in
Previous page
1/268
Next page
EN
32
Operation
Press GO
Total time
253h47m
First operation
Date: 13/03/08
Operation
Press GO
Operation
Press GO
Operation
Press GO
Total time
253h47m
Total time
253h47m
Total time
253h47m
First operation
Date: 13/03/08
First operation
Date: 13/03/08
First operation
Date: 13/03/08
Figure 2.12
Operation menu
Figure 2.9
Eco mode menu
2.2.5 Language
Allows the user the option of viewing the LCD text in several different language versions.
2.2.6 ECO Mode
The ECO (Economic) mode feature enables operating Robomow using minimum energy
required to cut the grass and maintain the lawn. The ECO mode default is set to 'on'.
Operation in ECO mode reduces Robomow noise level during operation and allows longer
operation time. It is recommended to use the ECO mode only in zones with Base Station,
where mowing is more frequent and a shorter part of the grass is cut. If Robomow detects
high grass it will automatically increase the power of the mowing motor to enable cutting
higher grass
.
2.2.7 Signal type
In some circumstances there may be interference to the wire signal caused by other wire signal
activated in adjacent lawn (neighbor that use robotic lawnmower) or by any other appliance
using similar frequency. In case of signal interference, you may see one of the following
symptoms (usually close to the neighbor lawn):
a. Robomow is widely swinging when driving along the wire;
b. Robomow changes direction without reaching the wire;
c. Robomow crosses the wire outside the designated area;
d. 'Start inside' message is displayed although Robomow is inside the designated area and
the perimeter wire is connected in the right polarity;
If your mower faced one of the above symptoms, to change the signal type call to service
2.2.8 Wire Position
Allows user to test the wire position in ‘Edge’ mode while the mowing motors are switched off to
prevent any damage to the perimeter wire after the initial setup of the wire is completed.
2.2.9 Delay operation
This option allows the user to press GO but delay the operation starting time. It is useful when you
want to start the operation later in the day when the grass is dry and not early in the morning
when the grass is wet (and you have to leave for work).
To use this option, follow the steps below:
- Set the ‘Delay operation’ to X hours (choose between 1,2,3…or up to 8 hours);
- Switch on the Perimeter Switch (It is operated for 12 hours) and place the mower inside the
lawn towards the perimeter wire;
- Pressing ‘STOP’ then ‘GO’ (while holding the ‘STOP’ button) will change the display to ‘Press
GO again to skip edge’ and at the end of the warming up process, the mower will stay in place
with a message ‘Operation delayed – wait…’
- The mower will start the operation after X hours (as set in the ‘Delay operation’ menu) from the
‘GO’ pressing.
2.3 Information
The ‘Information’ display (refer to figure 2.1) is used for information only, it allows the option to
scroll between the following menus:
2.3.1 Operation
Total time - Indicates the total number of hours the mower has been in operation.
First operation
– Indicates the date, in which the mower was first operated.
Eco mode
Press GO
Eco mode on
Press GO
Eco mode of
f
Confirm
… 86 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow Tuscania 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow Tuscania 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info