512484

Robomow Tuscania 500 Manual

77
Zoom out
Zoom in
Previous page
1/268
Next page
EN
23
Figure 1.34
Placement of stakes
Figure 1.34
Placement of stakes
Base position
Press GO to test
Press ‘GO’to test
the Base Station position
Searching base
Peg base
then press GO
If Robomow fails
to enter the Base
Station, it will stop
Follow the Robomow and
confirm that it docks properly
into the Base Station
Reposition Base
Press GO
Slightly move the Base Station, so that Robomow
enters the Base Station as centered as possible;
Reposition Robomow and press ‘GO’ for retesting
Fasten the base in place
using the 2 stakes (figure
1.34) and press ‘GO’
Wire position
Press GO to test
Press ‘GO’to test
wire position
Wire position
Robomow collides
with obstacle, drives
back and stops
Adjust wire
then press GO
Adjust the wire and press ‘GO’to
continue testing the wire position
Walk along the side of the
Robomow while it is following
the edge until completing one
lope of the perimeter without
striking any object (it will stay
in the Base Station).
Robomow enters successfully;
drives back from the Base
Station and stops;
Base position
Press GO to test
Base position
Press GO to test
Press ‘GO’to test
the Base Station position
Searching base
Peg base
then press GO
Peg base
then press GO
If Robomow fails
to enter the Base
Station, it will stop
Follow the Robomow and
confirm that it docks properly
into the Base Station
Reposition Base
Press GO
Slightly move the Base Station, so that Robomow
enters the Base Station as centered as possible;
Reposition Robomow and press ‘GO’ for retesting
Fasten the base in place
using the 2 stakes (figure
1.34) and press ‘GO’
Wire position
Press GO to test
Wire position
Press GO to test
Press ‘GO’to test
wire position
Wire positionWire position
Robomow collides
with obstacle, drives
back and stops
Adjust wire
then press GO
Adjust wire
then press GO
Adjust the wire and press ‘GO’to
continue testing the wire position
Walk along the side of the
Robomow while it is following
the edge until completing one
lope of the perimeter without
striking any object (it will stay
in the Base Station).
Robomow enters successfully;
drives back from the Base
Station and stops;
1.6 Testing the Base Station and Perimeter Wire Position
It is required to test the position of the Base Station and the Perimeter Wire to determine if any
small adjustments need to be made.
Position the Robomow inside the lawn towards the perimeter wire, at least 2 meters from the
Base Station (figure 1.30) and press the ‘GO’ button.
In a case you forgot to connect the Power Supply to a regular household receptacle 230 Volts
(120V), ‘
No wire signal’ message will be displayed on the LCD upon pressing GO, reminding
you to connect the Power Supply (Figure 1.31).
In a case you connected the Perimeter Wire in the opposite direction, ‘Change wires in plot
connector’
message will be displayed upon pressing GO, instructing you to switch between the
two wires connected to the Plot connector (Figure 1.32).
Follow the instructions, as shown in figure 1.33 to complete the test of the Base Station position:
Figure 1.30
Testing the Base Station position
Figure 1.33
Testing the Base Station and
Perimeter Wire Position
No wire signal
Press GO
No wire signal
Press GO
Figure 1.31
‘No wire signal’
messa
g
e
Change wires in
Plot connector
Change wires in
Plot connector
Figure 1.32
If the following
message is
displayed –
switch between the
2 wires connected to
the Plot connector
… 77 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow Tuscania 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow Tuscania 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info