537222
38
Zoom out
Zoom in
Previous page
1/50
Next page
38
code displayed prior to stopping, press the OK
button on the mower.
The following table displays all Error Codes and gives possible causes and corrective actions:
Display Message Probable Cause/Event Correcve Acons
E 1
Stuck in Place
- Robomow got stuck in place. It
cannot continue driving.
- Drive wheel motors have been
working under a severe load.
- Robomow has difculty turning in
place because the front wheel is
blocked by a ditch or non-level
ground.
- Remove the mower away from this
particular location and restart operation.
- Rectify the reason for it getting stuck.
- Check the ground around the mower for
ditches or non-level ground. Fill with dirt
and level off.
- Check if the drive wheels are free to rotate
and nothing is blocking them.
- Verify that the cutting height is not set too
low for the grass condition - increase the
cutting height if needed.
E 2
The mower is
Outside
- The Perimeter Wire is too close
to the edge of the lawn.
- The Perimeter Wire has been
laid the wrong way around a
perimeter island.
- The lawn slope is too steep
along the edge.
- Robomow does not succeed to
turn in place at the edge and it I
causing the mower to slip out of
the designated area.
- Automatic operation is initiated
while the robot is placed out of
the Perimeter Wire loop.
- Check that the Perimeter Wire is not
too close to the edge - remove the wire
towards the inner side of the lawn.
- Conrm that the Perimeter Wire has been
laid according to the instructions in the
Manual.
- Do not include areas with very steep
slopes.
- Verify that the cutting height is not set too
low - Increase the cutting height.
- Place the mower inside the lawn and
renew the operation.
E 3
No Wire Signal
- Power Box/Perimeter Switch is not
turned on or not connected
- The Perimeter Wire is not
connected to the Base Station/
Perimeter Switch.
- The Perimeter Wire is cut.
- Make sure the Base Station is connected to
the mains supply.
- Disconnect the Power Box from the mains
power and reconnect after 10 seconds.
- Check that the low voltage cable between
the Power Box and the Base Station is
connected.
- Check the LED indications on the Power
Box.
- Check the connection of the Perimeter Wire
to the Base Station / Perimeter Switch.
- Check the installation for cut wire. Repair
broken cable with the waterproofed
connector supplied in the box.
E 4
Check Power
- Power Box is not plugged in
properly into the power outlet.
- No power at the power outlet or
the main power is shut off.
- The mower or Base Station
contacts are dirty.
- Charging is not detected, although
there is a physical contact between
the mower and the Base Station
contacts.
- Conrm Power Box is plugged into the
power outlet.
- Turn power on to the power outlet.
- Check the power outlet using another
appliance.
- Clean the contacts with a brush or piece of
cloth.
- Conrm a good connection of the Power
Box to the Base Station.
E 5
Check Blade /
Cutting Height
- Mowing motor has faced over-
current conditions for too long
as a result of high grass or an
obstacle that is stuck or wrapped
around the blade.
- Something is preventing a blade
from rotating freely (Accumulated
grass clippings under the mowing
deck; rope or similar object
wrapped around mowing blade).
- CAUTION – Switch off the Safety Switch
before checking the blade.
- Inspect blade for foreign material or debris
preventing rotation.
- Clean out accumulated grass clippings using
a wooden stick.
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow TC300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow TC300 in the language / languages: English as an attachment in your email.

The manual is 3,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow TC300

Robomow TC300 User Manual - German - 50 pages

Robomow TC300 User Manual - Dutch - 50 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info