644648
38
Zoom out
Zoom in
Previous page
1/52
Next page
38
8. Charging
8.1 Charging During the Season
The Base Station is the primary charging source when Robomow is docked and will maintain the optimal battery
charge while awaiting departure.
8.2 Charging Out of Season
During out of season months, such as winter, it is required to:
Fully charge the battery in the Base Station till
the Battery indicator is green and lit constantly.
Note! The Safety Switch should be in ‘On’
position during charging.
LED indicators for charging:
- Red is lit constantly – Charge the battery.
- Green is blinking – During battery charging.
- Green is lit constantly – Battery is fully charged.
Remove Robomow from its Base Station. Turn
the Safety Switch off and store the mower in a
room temperature.
If the mower is stored for more than 3 months,
it is required to recharge the battery every 3
months till the Battery indicator shows it is fully
charged.
The charging can be done in one of the following
options:
1.
Place the mower in the Base Station for charging.
2.
Connect Robomow directly to the Power Box as follows:
- Disconnect the DC Cable coming from the Power Box
to the 15m Extension Cable and connect it to the rear
side of the mower as shown in the gure to the right.
Once the season starts, just place Robomow in
its Base Station to begin automatic operation.
!
IMPORTANT
!
Always charge your mower in a horizontal position. The mower should be at on the
ground while connected to the Power supply.
9. Troubleshooting and User Messages
9.1 General Error Codes
Robomow continuously monitors its operation. It produces error codes to assist you in running it smoothly.
A sticker containing the most common error codes is provided in the box. You can place it on the mower for your
convenience.
E9* (See Troubleshooting in Manual) represents
stops and error that are not very common, and
thus they are not shown in the above Error Code
Table. If E9 is displayed, press the RIGHT arrow
to receive the Error Code reason, for which
the mower has stopped and refer to the User
Manual for more details.
Usually, if the mower stops, an error code is
displayed. This display stays on for 5 minutes. If
you arrive later than those 5 minutes, the display
will be blank.
To wake Robomow up and see the last error
code displayed prior to stopping, press the OK
button on the mower.
Robomow Error Codes Table
E 1 Stuck in Place
E 2 Mower is Outside
E 3 No Wire Signal
E 4 Check Power
E 5 Check Blade / Cutting Height
E 6
Check Drive
E 7 Front Wheel Problem
E 8 Decrease Inactive Time
E 9* See Troubleshooting in Manual
E5XX
Call Support
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow TC1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow TC1000 in the language / languages: English as an attachment in your email.

The manual is 3,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow TC1000

Robomow TC1000 Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info