644643
51
Zoom out
Zoom in
Previous page
1/62
Next page
40
Troubleshooting
7.3 Other Problems
Problem
Encountered
Probable Cause/Event Corrective/User Action
Poor quality of
mowing
- Dull blade
- Switch between the two blades to use the sharp side,
which was not used yet.
- Replace blades.
- Grass is too high in relation to the set cutting
height.
- It is recommended to cut less than 1/3 of the green part of
the grass.
- Set the cutting height to a higher position and then
successively lower.
- If it is the fast growing season – use Robomow more
frequently to maintain the lawn (see Section 4.3.2 –
Mowing Extent).
- Grass is wet.
- Accumulation of grass clippings around the
blade.
- For best cut, operate Robomow when the grass is dry. It is
recommended not to mow in the early morning hours.
- Switch off the Safety Switch and use heavy gloves to
clean and remove the grass clippings.
Mower doesn’t
find the Base
Station or the
mower acquires
adjacent wire while
following the wire
in Near Wire Follow
mode
- There is a Perimeter Island / Obstacle or
Narrow Passage that prevents the mower to
complete its drive towards the Base Station
in Near Wire Follow mode.
- Reduce the Near Wire Follow Distance in the menu from
the default 7.
Mower does not
dock properly
and sometimes
misses the Base
Station contacts
- Height differences between the lawn and the
Base Station surface.
- Fill some ground to flat the lawn with the Base Station to
allow smooth entrance to the station.
- Wire underneath the Base Station is not tight
and placed in the middle of the Station.
- Confirm the wire underneath the Base Station is straight
tighten and centered below the Base Station.
- Base Station is setup on a side slope. - Move the Base Station to a relatively level ground.
- The Base Station is placed too close to the
corner of the lawn
- Move the Base Station to minimum 3 meters after a corner.
Mower doesn’t
depart from the
Base Station for a
long time
- There are several possible reasons for a
non-departure, including inactive times, rain
detection, etc.
- Press and hold ‘UP Arrow’ button for 1 second while the
mower is in the Base Station. The non-depart reason code
will be displayed for 3 seconds. Refer to Section 7.3.1 for
detailed description of non-depart codes.
Uneven mowing
results
- Robomow does not complete mowing at the
min. time, due to inactive time during the
Mowing Cycle.
- Minimize the Inactive Time windows to allow Robomow to
complete the Mowing Cycle faster and to achieve an even
mowing result.
- Grass is growing very fast.
- If it is the fast growing season – reduce the time between
mowing cycles (refer to Section 4.3.2.2 – Mowing
Frequency).
- Lawn shape is complicated (Narrow
Passages, obstacle and islands).
- In complicated lawns the mower takes more time on the
lawn to achieve better mowing results.
Increase the Mowing Hours (%) (refer to Section 4.3.2.1).
- The mowed area is smaller than the actual
lawn area.
- Increase the zone area (refer to Section 4.3.3 Edit an
existing Zone).
Robomow
operates at the
wrong time.
- The Inactive Time data (days and Hours)
are incorrect.
- Verify that the time in the mower is set correctly.
- Set the time (refer to Section 4.4.4 Time and Date).
- Reset the Inactive Time (refer to Section 4.3.1 Set
Inactive Operating Time(s)).
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RS625 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RS625 in the language / languages: English as an attachment in your email.

The manual is 16,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RS625

Robomow RS625 Quick start guide - English - 4 pages

Robomow RS625 User Manual - German - 62 pages

Robomow RS625 User Manual - Dutch - 64 pages

Robomow RS625 User Manual - French - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info