644643
24
Zoom out
Zoom in
Previous page
1/62
Next page
13
Initial Setup
2.3.3 A pond, swimming pool, or watercourse at lawn’s edge
OR:
Grass level more than 70 cm (2 ft.) higher than outer area.
P Set the Perimeter Wire at least 1.2 m (4 ft.) from the water (or chasm).
P You may provide a fence or another barrier along the lawn’s edge by the
water, so Robomow will surely detect it.
) The barrier should be at least 15 cm (6 inch) high. This will
block Robomow, under all circumstances, from crossing over the
Perimeter Wire into the water area.
) If such a barrier exists, you may set the Perimeter Wire at the Long
distance of 40 cm (16 inches) from the barrier.
2.4 Fastening Perimeter Wire to the Ground
P It is not necessary to bury the Perimeter Wire,
though you may do so, up to 5 cm (2 inches) deep.
P Consider burying the wire at exposed areas, such as pavements or
other areas with frequent pedestrian traffic.
P Pull the wire tight while hammering the peg to its final depth
in the ground.
WARNING !
Protect your eyes!
Protect your hands!
Use proper eye protection and wear appropriate work gloves when
hammering the pegs. Hard or dry ground may cause pegs to break when
driving them in.
P Insert the pegs at distances that will keep the wire down below the grass
level and prevent the wire from becoming a tripping hazard.
) The wire and the pegs will soon become
invisible under the growth of new grass.
P If additional wire is required in order to complete the setup,
connect it using the water-proof wire connectors supplied
with Robomow. (See Section 9.4 – Splicing the Perimeter Wire).
Use only the wire connectors supplied with Robomow.
Neither Twisted cables, nor a screw terminal insulated with insulation tape
are a satisfactory splice.
Soil moisture will make other conductors oxidize, which will later cause a
broken circuit.
2.5 Back at the Base Station – Completing the Perimeter
Wire Setup
Once the Perimeter Wire loop is completed and pegged to the ground, you
complete the setup by attaching the beginning and the end of the Perimeter
Wire to the Base Station Head.
P Hold both ends of the Perimeter Wire: the wire that
started the loop is the one with an attached connector.
P Peg the two Perimeter Wires down to the ground using the same peg
and leaving enough loose wire.
P Twist the two wires. A proper twist of the wires is crucial for robust
docking of Robomow at the Base Station.
EN
At least
1.2 m (4 ft.)
At least
40 cm (16”)
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RS625 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RS625 in the language / languages: English as an attachment in your email.

The manual is 16,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RS625

Robomow RS625 Quick start guide - English - 4 pages

Robomow RS625 User Manual - German - 62 pages

Robomow RS625 User Manual - Dutch - 64 pages

Robomow RS625 User Manual - French - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info