644642
50
Zoom out
Zoom in
Previous page
1/62
Next page
39
Robomow S models
Message
Displayed
Probable Cause/Event Corrective/User Action
Recharge battery
- The maximum operating time has been
reached (displayed in non-Base Station zone).
- Mower is searching for the Base Station but
the battery voltage is too low to continue the
searching process.
- Connect the charger to the mower or place it in the Base
Station for charging.
- Drive the mower manually using the remote control or
carry it by hand for charging in the Base Station.
Start elsewhere
- Drive wheel motors have been working under
a severe load during automatic or manual
operation.
- Check to insure the mower is not stuck, allowing the
drive wheels to slip.
- Check the ground around the mower for holes or
indentations. Fill with dirt and level off.
- Check if the drive wheels are free to rotate and nothing
blocks them.
- Remove the mower away from this particular location
and restart operation.
Start inside
- Automatic operation is initiated while the robot
is placed out of the Perimeter Wire loop.
- Place the mower inside the lawn and press the
button.
- Swap wires in the plot connector.
Stuck in place
- Robomow got stuck in place. It cannot continue
driving.
- Check the ground for holes or indentations, where the
mower has stopped and fill it with dirt and level off –
especially in the area close to the perimeter, where the
Robomow turns in place.
- Robomow has difficulty to turn in place
because the front wheel is blocked by a hole
or indentation. It caused the mower to turn in
place without detecting wire or bumper.
- Verify that the area is not too steep.
- Work mainly in dry conditions.
- Check if the Perimeter Wire is not too close to the edge
– move if required.
- Verify that the mowing deck is not set too low.
Sub-Zone X
Problem
- Sub-Zone 1/2/3/4 entry problem.
- The mower either fails to leave / bypass the
Base Station on its way to the Sub-Zone, or
fails to enter the Sub-Zone.
- The mower will try to reach the Sub-Zone every
two hours. If the mower fails to reach the Sub-
Zone within three attempts, it will stay in the
Base Station until the end of current mowing
cycle. It will not skip to the next Sub-Zone (if
there are any), if it fails to reach the current one.
- Try to start manual mowing (refer to section 4.5 –
Manual Operation). Check if something disturbs
mower’s driving backwards and/or bypassing the Base
Station. Confirm the mower drives along the perimeter
wire and doesn’t fall off the lawn’s edge, when it departs
from the Base Station.
- Confirm that the mower is able to follow the perimeter
wire along the narrow pass until it reaches the Sub-
Zone. Refer to section 2.2.2 for instructions on how to
set a narrow pass properly.
Switch off
before lifting
- The user carries Robomow manually while the
Safety Switch is On.
- Switch Off the Safety Switch before carrying Robomow.
Waiting for
Signal…
- Robomow has stopped the operation: it does
not detect a signal.
- Check the power to the Power Box.
- It may be an electrical power interruption. There is no
need to do anything. Robomow will renew operation as
soon as power is back.
- תועמשמשיםא,ךרוצןיאםא
EN
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RS615 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RS615 in the language / languages: English as an attachment in your email.

The manual is 16,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RS615

Robomow RS615 Quick start guide - English - 4 pages

Robomow RS615 User Manual - German - 62 pages

Robomow RS615 User Manual - Dutch - 64 pages

Robomow RS615 User Manual - French - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info