512472
53
Zoom out
Zoom in
Previous page
1/60
Next page
53
Base Station / Perimeter Switch
It is recommended to remove the
Base Station for the winter period:
- Disconnect the power supply from the mains power;
- Open the Base Station / Perimeter Switch cover;
- Disconnect all connectors from the board;
- You can now remove the Base Station cover/ Perimeter Switch and place it in dry storage;
- It is recommended to store the power supply in a dry storage; if not possible, protect the cable
end from moisture to prevent corrosion while not connected to the Base Station.
- Disconnect the green plot connector (keep it connected on the board for the next season) from
the perimeter wire ends and protect it from moisture to prevent corrosion of the wires while not
connected to the Base Station; You may place the Friendly Robotics wire nut connector onto both
wire ends for protection in the winter.
- Protect the remaining connector using the black rubber cover.
After Winter Storage
- Confirm that all connections, charging pins and wire ends are clean prior the first operation; if
required, clean the contacts with a small piece of fine sandpaper, 200 grit or higher or using steel
wool of ‘00’ or higher grade.
- Place the Base Station in its place and connect all cables to the board;
- Confirm that Robomow displays the correct time and date.
5.8 Batteries Replacement
WARNING! Follow the instructions below.
Complete replacement of one battery before starting to replace the
second battery.
Replacing the batteries:
- Lift the bumper and remove the batteries fuse;
- Remove the cutting height adjustment knob by lifting it
upwards (figure 5.4)
- Unscrew the five nuts manually at the rear side of the
Chassis cover (figure 5.5). If you find it difficult use a wide
flat screwdriver;
- Lift the rear side of the cover (see figure 5.6) and
disconnect only the two cables from the left battery (figure
5.7);
- Place the new battery and connect the cables to the
battery tabs when the red and the black cables are fitted
to the color on the battery;
- Disconnect the cables from the right battery;
- Place the new battery and slightly crimp the battery
connectors with plyers, so that they fit tightly on the
battery tabs.
- Connect the cables to the battery tabs respectively by
color;
- Place the cover back in its position and screw the five
nuts manually, confirm they are tight enough;
- Insert the batteries fuse and confirm the Robomow wakes
up.
Figure 5.4
Figure 5.5
Figure 5.7
Figure 5.6
Figure 5.5
Figure 5.4
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RM510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RM510 in the language / languages: English as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RM510

Robomow RM510 User Manual - German - 60 pages

Robomow RM510 User Manual - Dutch - 60 pages

Robomow RM510 User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info