512474
32
Zoom out
Zoom in
Previous page
1/44
Next page
32
Problem
Encountered
Probable Cause/Event Corrective/User Action
LCD display is in a
foreign language.
- The language setting was changed or
not correctly set.
- Place the mower out of the Base Station
and follow the sequence listed;
- Press ‘STOP’ button few times to confirm it
is on the main display
- Press ‘UP’ button twice
- Press ‘GO’ button once
- Press ‘Down’ arrow button once
- Press ‘GO’ button once
- Press ‘Down’ arrow button 4 times
- Press ‘GO’ button once
- Using the arrow, scroll to the correct
language
- Press ‘GO’ to confirm this selection
- Important! It is possible to see the last 10 battery run times and the battery voltage at
the beginning of the operation in the ‘Information’ menu (refer to paragraph 2.3.2)
- Battery is not fully charged at the
beginning of the operation
- Confirm the battery icon is fully and not
changed (while charging in the Base
Station) or ‘Ready keep charging’ message
is displayed (while charging through power
supply) prior the operation.
- ‘Work Time ‘ for that zone is set to
specific time and not to ‘MAX’
-Work time’ can be changed under ‘Zones
setup’ menu
- Grass is extremely over grown or very
wet.
- Raise cutting height.
- Always mow the grass frequently enough to
prevent over growth.
- CAUTION – Remove battery fuse before
lifting the mower
- Inspect blades for foreign material or debris
preventing rotation.
- Clean out accumulated grass clippings
using a wooden stick.
Short run time,
operates less time
than normal
- Batteries are reaching a normal end of
life state.
- Replace batteries.
- Confirm that the time in the mower is
set correctly (hour and date)
- Set the time (See paragraph 2.2.3)
Robomow operates
at the wrong times
- The GO’ button was pressed with no
meaning, by someone or by a pet
(‘Last stop cause’ under the
Information’ menu should be 805).
- To prevent unintended operation you can
activate the ‘Child guard’ or the ‘Anti theft’
options, which requires pressing of few
buttons in order to start the operation.
- Wire disconnected from perimeter
switch or from the Base Station.
- Confirm wire is plugged in and wire leads
are firmly attached.
- Perimeter wire cut
- Walk along perimeter, including islands and
look for obvious cuts or breaks in the wire.
Repair with Robomow wire splice
connectors.
'Cut wire’ indicator
flashing on
Perimeter Switch
or
the Base Station
beeps continuously
for 'Cut wire’
- Poor connections
- Check and repair all loose/poor or corroded
connections.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RM200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RM200 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RM200

Robomow RM200 User Manual - German - 44 pages

Robomow RM200 User Manual - Dutch - 44 pages

Robomow RM200 User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info