512474
28
Zoom out
Zoom in
Previous page
1/44
Next page
28
Message
Displayed
Probable Cause/Event Corrective/User Action
Cross wire
- The perimeter wire is too close to the edge
- The lawn slope is too big
- Robomow does not succeed to turn in place
at the edge and it causes the mower to slip
out of the area.
- Cutting height too low for the lawn and grass
conditions.
- Move the wire towards the inner side of
the lawn and do not include area with
slopes that are too big.
- Fill any holes and pits in the ground.
- Increase the cutting height
- The drive motors have been working under a
severe load for too long.
- There is no need to do anything
Robomow will renew automatically the
operation, as the drive motor will cool
down.
Drive overheat
cooling, wait…
Short-circuit detected in Drive Motors. Contact your Service Dealer.
Enter code - The theft guard system is activated
- Enter the correct 4-digit code. ‘Theft
Guard’ can be deactivated under
Settings’. Contact your service provider
for assistance in a lost code situation.
Failure: xyz
- Internal failure
- Press ‘go’ to confirm the message; if
the message is still displayed, remove
the battery fuse for 10 seconds and
retry to operate the mower. If the
message still displayed, contact your
service dealer.
CAUTION – Remove battery fuse before
lifting the mower
- The Robomow has driven onto an
obstacle, raising the front end. Remove
or exclude this object from the mowing
area.
- The Robomow is being used on a slope
too steep for safe mowing. Exclude this
from the mowing area.
- High grass is preventing the front wheel
from fully riding on the ground. Raise
the cutting height.
Frnt wheel prob
- The Front Wheel has left the ground for
more than 8 – 10 seconds.
- The ground contains large holes or
indentions where the front wheel can
drop into when passing across. Fill
these areas with dirt and level off.
High temperature
waiting…
- Robomow is charged and the ambience
temperature is out of range (above 158ºF /
70ºC);
- Do not do anything, the charging is
stopped and Robomow is waiting for
temperature to change back to the
allowed range; if temperature stays out
of the range for more than 12 hours, the
message is changed to ‘High temp.
Press GO’.
Insert fuse
for charging
- Robomow is connected to charging without a
battery fuse
- Disconnect Robomow from charging,
insert the battery fuse and reconnect to
charging.
Keep charging
if not used
- Message is displayed every time the power
supply is disconnected.
- Displayed when the mower isn’t in operation
and not connected to the charging for a long
time.
- Press any key to change the display
back.
- Send the mower back to the Base
Station for charging / connect the power
supply or continue in operation.
Key pressed
- One of the operating panel buttons is
constantly pressed.
- Press GO’ to confirm the message and
to continue in operation. The message
is displayed to inform the user about
the problem, but will not prevent the
operation.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RM200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RM200 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RM200

Robomow RM200 User Manual - German - 44 pages

Robomow RM200 User Manual - Dutch - 44 pages

Robomow RM200 User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info