664046
47
Zoom out
Zoom in
Previous page
1/58
Next page
46
9.3 User Messages
The next table gives information about User Messages that can be displayed on the mower:
Display Message / Descripon Required Acon
BATT
Recharge Battery. Low battery voltage. Recharge the Battery.
PAUS
Automatic operation is paused via the Power Box
or the Program On/Off menu.
Enable automatic operation on the Power Box
or via the Program On/Off menu (refer to section
7.3 or section 6.4.2, menu P021).
U001
Test Base Station position.
Displayed during the One-Time Setup.
Refer to section 5.2.5 in the User Manual.
U002
Peg Base Station.
Displayed during the One-Time Setup.
Refer to section 5.2.5 in the User Manual.
U003
Test wire position.
Displayed during the One-Time Setup.
Refer to section 5.2.6 in the User Manual
U004
Wire Test ended (during the One-Time Setup)
Displayed only when using the Robomow App.
No action is required.
U009
Wait for the operational data to be sent
No action is required. As soon as the
operational data has been sent, the charging
will start. This may take a couple of minutes.
U017
Operation time is completed as expected. No action is required.
U018
Operation time is shorter than expected Battery run time is too short. Replace Battery.
U024
Keep charging if not used.
Displayed only if the mower is disconnected from
a Charging Adaptor.
It is recommended to keep the mower
connected to the Power Supply when not in use.
U025
Switch Off before lifting
It is required to switch Off the System Switch
before lifting and carrying the mower.
U029
Change the wires in plot connector
Displayed during the One-Time Setup.
Swap the wires at the plot connector.
Refer to section 5.2.5 in the User Manual.
U032
Switch on the System Switch.
Displayed if the mower is connected to charging,
but the System Switch is ‘Off’.
Switch the System Switch to ‘On’.
U041
Press the STOP button at Sub-Zone entry.
Press STOP at the point you want the mower to
start mowing the Sub-Zone.
U042
Learning edge distance.
The mower learns the distance of the Perimeter
Wire in a Separated Zone. Press STOP to learn
the distance.
U043
Going to Sub-Zone entry point. Displayed when
the mower drives towards the Sub-Zone.
No action is required.
U044
Place the mower in the Base Station.
Place the mower in the Base Station before
starting the process of adding a Sub-Zone.
U051
Reposition the Base Station position.
Displayed during the One-Time Setup.
Refer to section 5.2.5 in the User Manual.
U052
Adjust Wire Refer to section 5.2.6 in the User Manual.
U062
An alarm will soon be activated.
This message warns you to enter the PIN code
before the Anti-Theft alarm will sound.
U064
The Searching Base Station operation cannot be
performed
When choosing the ‘Home’ button in a zone
without a Base Station.
U086
Waiting for the signal…
Robomow has stopped the operation. It does not
detect a signal.
Check the power to the Power Box.
There may be an electrical power interruption.
There is no need to do anything. Robomow will
renew operation as soon as the power is back
on.
U087
Mow motor overheat, Cooling…
The mowing motor has been working under a
severe load for too long.
No need for action – Robomow will renew
automatically the operation, as the mowing
motor will cool down.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RC312u at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RC312u in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RC312u

Robomow RC312u Quick start guide - English - 4 pages

Robomow RC312u User Manual - German - 58 pages

Robomow RC312u User Manual - Dutch - 58 pages

Robomow RC312u User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info