664045
49
Zoom out
Zoom in
Previous page
1/58
Next page
48
Problem
Encountered
Probable Cause/Event Correcve Acons
Mower does not
dock properly
and sometimes
misses the Base
Station contacts
- Height differences between the lawn and
the Base Station surface.
- FillsomegroundtoattenthelawntotheBase
Station to allow smooth entrance.
- The wire underneath the Base Station is
not tight and placed in the middle of the
Station.
- ConrmthewireunderneaththeBaseStation
is straight, tight, and centered below the Base
Station.
- The Base Station is set up on a side
slope.
- Move the Base Station to a relatively level
ground.
- The Base Station is placed too close to
the corner of the lawn
- Move the Base Station so it is not within 3
meters after a corner.
Uneven mowing
results
- The time between operations is too long
because of long inactive time windows.
- Minimize the Inactive Time windows to allow
Robomow to complete the Mowing Cycle faster
and to achieve even mowing results.
- Grass is growing very fast.
- If it is during a fast growing season – change
the Mowing Frequency (refer to Section 6.4.2 –
P001).
- The shape of the lawn is complicated
(Narrow Passages, obstacle and islands).
- In a complicated lawn more time is required for
the mower to achieve better mowing results.
- Increase the mowing hours percentage (refer to
Section 6.4.1.2).
- The set area is smaller than the actual
lawn size.
- Increase the zone area (refer to Section 6.4.1.4)
Robomow
operates during
Inactive Time.
- Wrong clock time is set in the mower.
- Verify that the time on the mower is set correctly.
- Set the time (refer to Section 6.4.1.1).
- Reset the Inactive Time (refer to Section
6.4.1.3).
Robomow
operates during
rain
- Rain Sensor is disabled or its sensitivity
is set too low
- Enable the Rain Sensor and adjust its sensitivity
if required (refer to Section 6.4.2 – P007/p008)
- The Islands feature is set to On. In this
case the mower is searching for the base
by moving around the lawn. This special
search method takes more time, and
may create an impression that the mower
is still mowing, while in fact it is already
searching for the Base Station.
- No special action is required. For more
information about the Islands On/Off feature
refer to Section 6.4.2 – P002)
Cut wire indicator
isashingon
Power Box
- The Extension Cable is disconnected or
damaged between Power Box and the
Base Station.
- ConrmtheExtensionCableispluggedinand
wireleadsarermlyattached.
- Perimeter Wire is cut.
- Walk along Perimeter Wire.
- Look for cuts or breaks in the wire.
- Repair with Robomow wire splice connectors.
- Scan the code and
watch the video
demonstrating the
Corrective Actions of
the “Perimeter Wire
is cut”.
The poor
connection
indicator is
ashingon
Power Box
- Poor connections
- Check and repair all loose, poor, or corroded
connections.
- Twisted cables or a screw terminal which
is insulated with insulation tape is not a
satisfactory splice.
- Soil moisture causes the conductors to
oxidize.
- Use the connectors supplied in the box. They
are waterproof and give a reliable electrical
connection.
49


Need help? Post your question in this forum.

Forumrules
1

Forum

robomow-rc308u

Reset search

  • ROBOMOW304
    SERVUCE NANUAL
    ROTEM JOSEPH
    rotemj@bezeqint.net Submitted on 1-5-2022 at 18:08

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RC308u at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RC308u in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RC308u

Robomow RC308u Quick start guide - English - 4 pages

Robomow RC308u User Manual - German - 58 pages

Robomow RC308u User Manual - Dutch - 58 pages

Robomow RC308u User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info