664045
43
Zoom out
Zoom in
Previous page
1/58
Next page
42
Chapter 9 –
Troubleshooting and User Messages
9.1 General Error Codes
Robomow continuously monitors its operation.
It produces error codes to assist you in running it
smoothly.
A sticker containing the most common error codes
is provided in the box. You can place it on the mower
for your convenience.
(*) E9 (See Troubleshooting in Manual) represents
errors that are not very common, and thus they
are not shown in the above Error Code Table. If
E9 is displayed, press the LEFT arrow to receive
a detailed Error Code. Then refer to section 9.2 for
more details.
Usually, if the mower stops, an error code is
displayed. This display stays on for 5 minutes. If
you arrive later, the display will be blank.
To wake Robomow up and see the last error code displayed prior to stopping, press the OK button on the
mower.
The following table displays all Error Codes and gives possible causes and corrective actions:
Display Message Probable Cause/Event Correcve Acons
E1
Stuck in Place
- Robomow got stuck in place. It
cannot continue driving.
- Drive wheel motors have been
working under a severe load.
- Robomowhasdifcultyturning
in place because the front wheel
is blocked by a ditch or non-level
ground.
- Move the mower away from this particular
location and restart operation.
- Rectify the reason for it getting stuck.
- Check the ground around the mower for
ditches or non-level ground. Fill with dirt
and level off.
- Check if the drive wheels are free to rotate
and nothing is blocking them.
- Verify that the cutting height is not set too
low for the grass condition – increase the
cutting height if needed.
E2
The mower is
Outside
- The Perimeter Wire is too close
to the edge of the lawn.
- The Perimeter Wire has been
laid the wrong way around a
perimeter island.
- The lawn slope is too steep
along the edge.
- Robomow does not succeed to
turn in place at the edge, and it is
causing the mower to slip out of
the designated area.
- Automatic operation is initiated
while the robot is placed out of
the Perimeter Wire loop.
- Check that the Perimeter Wire is not
too close to the edge – remove the wire
towards the inner side of the lawn.
- ConrmthatthePerimeterWirehasbeen
laid according to the instructions in the
Manual.
- Do not include areas with very steep
slopes.
- Verify that the cutting height is not set too
low – Increase the cutting height.
- Place the mower inside the lawn and
renew the operation.
Robomow Error Codes Table
E1
Stuck in Place
E2
Mower is Outside
E3
No Wire Signal
E4
Check Power
E5
Check Blade / Cutting Height
E6
Check Drive
E7
Front Wheel Problem
E8
Decrease Inactive Time
E9*
See Troubleshooting in Manual
E5XX
Call Support
43


Need help? Post your question in this forum.

Forumrules
1

Forum

robomow-rc308u

Reset search

  • ROBOMOW304
    SERVUCE NANUAL
    ROTEM JOSEPH
    rotemj@bezeqint.net Submitted on 1-5-2022 at 18:08

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RC308u at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RC308u in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RC308u

Robomow RC308u Quick start guide - English - 4 pages

Robomow RC308u User Manual - German - 58 pages

Robomow RC308u User Manual - Dutch - 58 pages

Robomow RC308u User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info