664048

Robomow RC308 Pro Manual

48
Zoom out
Zoom in
Previous page
1/58
Next page
47
EN
Display Message / Descripon Required Acon
U088
Drive motor overheat, Cooling…
The drive motors have been working under a
severe load for too long.
No need to do anything.
Robomow will renew the operation automatically
as soon as the drive motor will cool down.
U089
Child Lock feature is activated.
The operational buttons are locked to prevent
unintended operation, especially by children.
Tooperatethemower,rstpressoneofthe
operating mode buttons and then to press the
OKbuttontoconrm.
U090-
U093
Sub-Zone 1/2/3/4 entry problem.
The mower eitherfails to leave/bypassthe Base
Station on its way to the Sub-Zone,orfails to enter
the Sub-Zone.
The mower will try to reach the Sub-Zone every
two hours. If the mower fails to reach the Sub-
Zone within threeattempts, it will stay in the Base
Station until the end of current mowing cycle.
The mower will not skip to the next Sub-Zone (if
there are any), if it fails to reach the current one.
Try to startmanual mowing (refer to section
6.3 – Manual Operation). Check if something
disturbs mower’s driving backwards and/or
bypassingtheBaseStation.Conrmthemower
drives along the perimeter wire and doesn’t fall
off the lawn’s edge, when it departs from the
Base Station.
Conrmthatthemowerisabletofollowthe
perimeter wire along the narrow pass untilit
reaches the Sub-Zone. Refer to section 4.3.3
for instructions on how to set a narrow pass
properly.
U094
Raise mowing height when activating the
TurboMow mode.
Refer to sections 5.1 and P026 in Section 6.4.2
in the User Manual.
9.4 Basic Troubleshoong
The next table will give details and possible causes of other faults, which do not provide error codes. If a fault
cannot be dealt with using these tables, please call your service provider.
Problem
Encountered
Probable Cause/Event Correcve Acons
Poor quality of
mowing
- Dull blade - Replace blade.
- The grass is too high in relation to the set
cutting height.
- It is recommended to cut less than a 1/3 of the
green part of the grass.
- Set the cutting height to a higher position and
then successively lower.
- If it is during a fast growing season – change
the Mowing Frequency (refer to Section 6.4.2 –
P001).
- The grass is wet and causes
accumulation of grass clippings around
the blade.
- For best cut, operate Robomow when the grass
is dry. Do no to mow in the early morning hours.
- Switch Off the Safety Switch and use heavy
gloves to clean and remove the grass clippings.
Mower doesn’t
ndtheBase
Station
- There is a Perimeter Island or a Narrow
Passage that prevents the mower to
complete its drive towards the Base
Station in Near Wire Follow mode.
- Reduce the Near Wire Follow Distance in the
Settings menu from the default 7.
Mower doesn’t
depart from the
Base Station for
a long time
- There are several possible reasons for a
non-departure, including inactive times,
rain detection, etc.
- Press and hold ‘Home’ button for 1 second
while the mower is in the Base Station. The
non-depart reason code will be displayed for
3 seconds. Refer to Section 9.4.1 for detailed
description of no-depart codes.
Robomow
is noisy and
vibrates
- Damaged or unbalanced blade
- Check if the lawn is free from branches, stones
or other objects that can damage the blade.
- Replace the blade
… 48 …


Need help? Post your question in this forum.

Forumrules
1

Forum

robomow-rc308-pro

Reset search

  • I have used my mower twice on manual recently with no problems. However I have set it up for Automatic and it is reading PAUS. In the manual it advises me to use the Automatic Operation On/of on my remote control, however I was never supplied with a remote control. Could you advise me how to override the PAUS button on my mower display panel. As I have been unable to contact your agent at present, I would appreciate your help. Thank you. Hedley Best. Submitted on 18-4-2020 at 15:33

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RC308 Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RC308 Pro in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RC308 Pro

Robomow RC308 Pro Quick start guide - English - 4 pages

Robomow RC308 Pro User Manual - German - 58 pages

Robomow RC308 Pro User Manual - Dutch - 58 pages

Robomow RC308 Pro User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info