537220

Robomow RC306 Manual

17
Zoom out
Zoom in
Previous page
1/50
Next page
17
4.2.1 Starting Point: Perimeter Wire at the Base Station area
.
• Place the Base Station, according to your plan, as shown in the
gure to the right.
• Do not place the Base Station within 3m (10 ft.) of a corner
• Select the roll of wire with a green plot connector attached to
the end.
• Pull the plot connector and some wire out of the plastic covering.
! Do not remove the spool of wire from its covering.
The plastic covering is the dispenser for the wire.
• Peg the beginning of the wire to the ground, where the Base
Station will be located. Pegs are supplied in the Robomow’s
box.
• Pull out 30 cm (12 inches) of wire and leave it loose near the
Base Station location. Later, at the end of the setup, this part of
the wire will close the Perimeter Wire loop.
• Start laying the wire in an anticlockwise direction.
• Continue to pull the Perimeter Wire out of its covering, laying it
loosely as you walk along the lawn edge.
! If you get to any area /object that needs care or special boundaries, make sure you carefully lay the
Perimeter Wire as needed. The next sections deal with such special cases.
4.2.2 Laying the Perimeter Wire
o The Perimeter Wire is secured to the ground by pegs
supplied with Robomow. Initially insert pegs every
few meters and at corners. At this early stage set a
minimum number of pegs. Later, after testing the wire
setup, you will insert all necessary pegs.
o After uncoiling some wire, before inserting pegs, use
the RoboRuler to determine the distance of the wire
from the lawn edge or obstacles.
• If the working area borders against a at area,
ower bed, small step (more than 1 cm), small ditch,
or a small elevation (up to 5 cm), the Perimeter Wire
should be laid 20 cm (8 inches) inside the working
area. This prevents the wheels from driving into a
ditch. Use the shorter distance of the RoboRuler to
set the distance of the wire from the lawn edge.
• If the edge is sloped (max 10% is allowed) or is
bordered with high obstacles such as a wall or fence,
the Perimeter Wire should be laid at a distance of
28 cm (11 inches) from the obstacle. Use the longer
distance of the RoboRuler to set the distance of the
wire from a wall.
Perimeter Wire
Peg
Min. 3m (10 ft)
from any corner
18cm (7”)
28cm from Wall (11”)
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RC306 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RC306 in the language / languages: English as an attachment in your email.

The manual is 3,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RC306

Robomow RC306 Quick start guide - English - 4 pages

Robomow RC306 User Manual - German - 50 pages

Robomow RC306 User Manual - Dutch - 50 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info