644650
46
Zoom out
Zoom in
Previous page
1/58
Next page
45
EN
Display Message Probable Cause/Event Correcve Acons
0022
Check mowing
motor
- Mowing motor has faced over-
current for too long in the Base
Station before starting the operation.
- CAUTION – Switch Off the Safety Switch
before checking the blade.
- Remove the mower from the Base Station.
Inspect the blade for foreign material or debris
preventing rotation.
0023
Check power - See E4 in the above table
0026
Base problem
- Robomow fails to enter the Base
Station several consecutive times.
- Adjust the Base Station position.
- Clean the contacts with a brush or piece of
cloth.
0027
Start Elsewhere
- Drive wheel motors have been
working under severe load during
automatic or manual operation.
- Check to insure the mower is not stuck,
causing the drive wheels to slip.
- Check the ground around the mower for holes
or indentations. Fill with ground and level off.
- Check if the drive wheels are free to rotate
and nothing is blocking them.
- Move the mower away from this particular
location and restart operation.
0028
Cross Outside
- The Perimeter Wire is too close to
the edge.
- The lawn slope is too steep.
- Robomow does not succeed to
turn in place at the edge and it
causes the mower to slip out of the
designated area.
- Robomow has slipped out of the
Perimeter Wire lope because of
sloping area or wet grass.
- Remove the wire towards the inner part of the
lawn.
- Do not include this area because of its steep
slopes.
- Fill holes and pits in the ground.
- Increase the cutting height.
0030
Start Inside
- Automatic operation is initiated
while the robot is placed out of the
Perimeter Wire loop.
- Place the mower inside the lawn and renew
the operation.
0031
Stuck in place - See E1 in the above table
0060
Check mowing
hours (%)
- The mowing hours % value you
have set is too high for your lawn
area.
- Decrease the mowing hours % you have set
for the zone(s) in your lawn.
0061
Decrease
Inactive Time
- See E8 in the above table
46


Need help? Post your question in this forum.

Forumrules
1

Forum

robomow-rc304---2016

Reset search

  • After putting my fully charged Robomow rc304 in it's base station after the winter, both lights are flashing on the power box. The battery icon is now red. I have checked all the connections. Turned it off then on after 10 seconds. No change, lights still flashing, no beeping. Submitted on 20-3-2020 at 19:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RC304 - 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RC304 - 2016 in the language / languages: English as an attachment in your email.

The manual is 5,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RC304 - 2016

Robomow RC304 - 2016 Quick start guide - English - 4 pages

Robomow RC304 - 2016 User Manual - German - 62 pages

Robomow RC304 - 2016 User Manual - Dutch - 62 pages

Robomow RC304 - 2016 User Manual - French - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info