Manual Robomow RC304 - 2016 (page 39 of 58) (English)

644650

Zoom out

Zoom in

1/58

Screen Seng Descripon Opons

P022

Add Sub-Zone

• Enables the addition of a Sub-Zone. Maximal number of Sub-

Zones may be different for each Robomow model.

• A1/A2/A3/A4 (name of the rst available sub-zone) is displayed

- press OK.

• If the mower is not at the Base Station, then ‘U044’ (“Place the

mower in the Base Station”) is displayed. Place the mower in the

Base Station and press OK.

• The mower will start moving towards the Sub-Zone.

• Scroll to set the area of the Sub-Zone and press OK.

• Note! This process is not a part of the One-Time Setup (see

Section 5.2)

• The area setting of a Sub-Zone can be later updated through the

‘Area’ menu of the Basic Settings (see Section 6.4.1)

• The distance to Sub-Zone’s entry point can be update later

through menu P023

A1/A2/A3/

100

P023

Update Distance

To Sub-Zone

• This menu is shown only if a Sub-Zone has been dened.

• It allows to update the distance to Sub-Zone’s entry point.

• Scroll to choose the required Sub-Zone (A1/A2/A3/A4) and press

OK to update the distance to the entry point.

P024

SmartMow

(Default = OFF)

• SmartMow feature allows more efcient mowing operation

through the smooth and continuous turns when reaching lawn’s

edge.

• When this feature is enabled for the rst time in a particular

zone, it may require the mower to cross the lawn and “touch”

the perimeter wire several times (to perform an initial calibration

of the algorithm), before it will start performing smooth turns at

lawn’s edge.

• If there is more than one zone dened, then there is an option

to enable this feature for a particular zone or for the entire lawn

(‘All’).

• Please note! This feature may not be equally efcient on all lawns

or on different sections of a particular lawn, especially if a lawn

area is small or has narrow areas, big islands or slopes.

All

/L2/L3

/A2/A3/

/OFF

P025

SmartMow

Edge Overlap

(Default = 10)

• Allows adjusting the degree of overlapping with lawn’s edge,

when performing the smooth and continuous turns in SmartMow

mode.

• Increasing this value will cause a higher overlapping with lawn’s

edge (for better mowing results), but at some point may prevent

the mower from performing a smooth turn.

• If there is more than one zone dened, this setting may be set per

zone or for the entire lawn (‘All’).

5-30

P026

TurboMow

(Default = OFF)

• TurboMow feature allows faster and stronger mowing of a high

grass during the rst cut of the season.

• When a mower is operated for the rst time, or if the Factory

Defaults (“Out of the Box” settings - see Section 5.2) are invoked,

this feature is automatically set to ON to provide better mowing

results already after the initial mowing cycle. At the end of the

initial mowing cycle, the feature will be automatically disabled (set

to OFF).

• This menu allows to activate TurboMow feature manually. ‘U094’

(“Raise mowing height when activating the TurboMow mode.”)

will be displayed. At the end of the cycle the feature will be

automatically deactivated (set to OFF).

• When the TurboMow feature is activated, the initial mowing cycle

will be longer and noisier than the next mowing cycles.

On/OFF

After putting my fully charged Robomow rc304 in it's base station after the winter, both lights are flashing on the power box. The battery icon is now red. I have checked all the connections. Turned it off then on after 10 seconds. No change, lights still flashing, no beeping. Submitted on 20-3-2020 at 19:49
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RC304 - 2016 in the language / languages: English as an attachment in your email.

The manual is 5,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RC304 - 2016

Robomow RC304 - 2016 Quick start guide - English - 4 pages

Robomow RC304 - 2016 User Manual - German - 62 pages

Robomow RC304 - 2016 User Manual - Dutch - 62 pages

Robomow RC304 - 2016 User Manual - French - 62 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Robomow RC304 - 2016 Manual

Product: