644650
27
Zoom out
Zoom in
Previous page
1/58
Next page
26
4.8 Setup in a Non-Base Zone
A Non-Base Zone is an area of the lawn that is not connected
to a Base Station.
A Perimeter Switch should be installed in these areas.
When necessary, the Perimeter Switch can be easily moved
to other zones.
4.8.1 Determining the Perimeter Switch Location
Consider the following in order to install the Perimeter
Switch at an optimal location:
• The Perimeter Switch is to be installed outside the
perimeter of the Non-Base Zone.
• Select a dry and sheltered location.
• The Perimeter Switch is to be mounted vertically.
• The Perimeter Switch is supplied with an indoor power supply. Choose a location close to a regular power outlet
(230V / 120V).
Note:
a rechargeable battery for the Perimeter Switch is available as an accessory (See Chapter 12 Robomow
Accessories).
4.8.2 Perimeter Switch placing options
• The Perimeter Switch connector is easily connected and disconnected. It
allows for quickly switching from one zone to another.
• You may use the large stake, attached to the back of the Perimeter Switch,
to easily insert it in and out of the ground.
• You may mount the Perimeter Switch on a vertical surface, such as a wall
or deck railing. Use the three marks on the back of the Perimeter Switch
cover.
4.8.3 Laying out the Perimeter Wire
The perimeter wire setup in a Base and Non-Base Zone are the
same, except for the starting point:
• The Perimeter Switch is placed out of the area (at least 1 meter /
3.3 ft. from the lawn).
• Start to lay the Perimeter Wire from the Perimeter Switch location.
• Lay the Perimeter Wire from the Perimeter Switch to the
lawn.
• Start laying the wire in anticlockwise direction.
The Perimeter Switch
MUST be Mounted
vertically in order to
maintain its’ water
resistance
Wires leading from the
lawn to the Perimeter
Switch are adjacent and
touching.
Min. 1m (3ft)
Min. 1m (3ft)
27


Need help? Post your question in this forum.

Forumrules
1

Forum

robomow-rc304---2016

Reset search

  • After putting my fully charged Robomow rc304 in it's base station after the winter, both lights are flashing on the power box. The battery icon is now red. I have checked all the connections. Turned it off then on after 10 seconds. No change, lights still flashing, no beeping. Submitted on 20-3-2020 at 19:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RC304 - 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RC304 - 2016 in the language / languages: English as an attachment in your email.

The manual is 5,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RC304 - 2016

Robomow RC304 - 2016 Quick start guide - English - 4 pages

Robomow RC304 - 2016 User Manual - German - 62 pages

Robomow RC304 - 2016 User Manual - Dutch - 62 pages

Robomow RC304 - 2016 User Manual - French - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info