537232
47
Zoom out
Zoom in
Previous page
1/54
Next page
37
Troubleshooting
EN
Problem
Encountered
Probable Cause/Event Corrective/User Action
Mower does not
dock properly and
sometimes miss
the Base Station
contacts
- Height differences between the lawn and the
Base Station surface.
- Fill some ground to flat the lawn with the Base Station to
allow smooth entrance to the station.
- Wire underneath the Base Station is not tight
and placed in the middle of the Station.
- Confirm the wire underneath the Base Station is straight
tighten and centered below the Base Station.
- Base Station is setup on a side slope. - Move the Base Station to a relatively level ground.
- A base station is placed too close to the
corner of the lawn
- Move the Base Station within 3 meters from a corner.
Uneven mowing
results
- Robomow does not complete mowing at the
min. time, due to inactive time during the
Mowing Cycle.
- Minimize the Inactive Time windows to allow Robomow
to complete the Mowing Cycle faster and to achieve even
mowing result.
- Grass is growing very fast.
- If it is the fast growing season - reduce the time between
mowing cycles (refer to Section 4.3.2 Increase /
Decrease Operations).
- Lawn shape is complicated shape, Narrow
Passages, obstacle and islands).
- In complicated lawn the mower takes more time on the
lawn to achieve better mowing results.
Increase the Intensity (refer to Section 4.3.2.1 Increase /
Decrease Operations).
- The mowed area is smaller than the actual
lawn area.
- Increase the zone area (refer to Section 4.3.3 Edit an
existing Zone).
Robomow
operates at the
wrong time.
- The Inactive Time data (days and Hours) is
incorrect.
- Verify that the time in the mower is set correctly.
- Set the time (refer to Section 4.4.4 Time and Date).
- Reset the Inactive Time (refer to Section 4.3.1 Set
Inactive Operating Time(s)).
Cut wire indicator
is flashing on
Power Box
- Cable is disconnected or damaged between
Power Box and the Base Station.
- Confirm cable is plugged in and wire leads are firmly
attached.
- Perimeter Wire is cut.
- Walk along Perimeter Wire.
Look for cuts or breaks in the wire.
Repair with Robomow wire splice connectors.
Poor connection
indicator is
flashing on Power
Box
- Poor connections - Check and repair all loose/poor or corroded connections.
- Twisted cables, or a screw terminal,
insulated with insulation tape is not a
satisfactory splice.
Soil moisture causes the conductors to
oxidize and after a while. This results in
broken circuit.
- Use the connectors supplied in the box. They are
waterproof and give a reliable electrical connection.
Robomow
is noisy and
vibrates
- Damaged or unbalanced blade
- Check if the lawn is free from branches, stones or other
objects that can damage the blade before operating the
Robomow.
- Replace the blade
LCD display
is in a foreign
language.
- The language setting was changed or not
correctly set.
- Press the CANCEL + DOWN buttons for more than 3
seconds. This is a shortcut to the Language menu.
Change the language.
Mowing or
charging times
are shorter than
usual.
- This behavior is normal at low temperatures
(below 15 ºC (59 ºF)).
- No action is required.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow MS1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow MS1800 in the language / languages: English as an attachment in your email.

The manual is 7,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow MS1800

Robomow MS1800 User Manual - German - 54 pages

Robomow MS1800 User Manual - Dutch - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info