537231
45
Zoom out
Zoom in
Previous page
1/54
Next page
35
Troubleshooting
EN
Message
Displayed
Probable Cause/Event Corrective/User Action
Cross Outside
- The Perimeter Wire is too close to the edge.
- The lawn slope is too big.
- Robomow does not succeed to turn in place at
the edge and it causes the mower to slip out of
the area.
- Robomow has slipped out of the Perimeter
Wire lope because of slopping area or wet
grass.
- Remove the wire towards the inner side of the lawn.
- Do not include area with very steep slopes.
- Fill holes and pits in the ground.
- Increase the cutting height.
Drive Overheat
Cooling…
- The drive motors have been working under a
severe load for too long.
- No need to do anything.
- Robomow will renew the operation automatically as
soon as the drive motor will cool down.
Front Wheel
Problem
- The Front Wheel has left the ground for too
long time during operation.
- If Robomow has driven onto an obstacle, raising the
front end:
Remove or exclude the object from the mowing area.
- If Robomow is being used on a slope too steep for safe
mowing:
Exclude this from the mowing area.
- If High grass is preventing the front wheel from fully
riding on the ground:
Raise the cutting height.
- If the ground contains large holes or indentations where
the front wheel can drop into when passing across:
Fill these areas with dirt and level off.
Handle Lifted
- The handle is lifted while trying to start the
operation
- Push the carrying handle down back to its position to
enable automatic operation.
Key Pressed
- One of the operating panel buttons is
constantly pressed.
- Press
to confirm the message and to continue
operation. This message is displayed to inform only.
Keys Locked
- Child Lock feature has been activated.
- Press the
button and then press the
button.
Child Lock can be deactivated under the Settings
menu.
Mow Overheat
cooling…
- The mowing motor has been working under a
severe load for too long of a time.
- No need for action – Robomow will renew automatically
the operation, as the mowing motor will cool down.
No wire signal
- Power Box / Perimeter Switch is not turned on
or not connected to the zone intended to mow.
- The Perimeter Wire is not connected to the
Base Station / Perimeter Switch.
- The Perimeter Wire is cut.
- Make sure the Base Station is connected to the mains
supply.
- Disconnect the Power Box from the mains power and
reconnect after 10 seconds.
- Check the Perimeter Switch is connected to the correct
zone and is turned on.
- Check the connection of the Perimeter Wire to the Base
Station / Perimeter Switch.
- Check for cut in the Perimeter Wire.
Rain detected
- The operation is delayed as Robomow detects
rain on the scheduled time it should start the
automatic operation from the Base Station.
- No need for action-
the message is displayed until the Robomow will not
detect rain and will start mowing.
Recharge battery
- The maximum operating time has been
reached (displayed in non-Base Station zone).
- Mower is searching for the Base Station but
the battery voltage is too low to continue the
searching process.
- Connect the charger to the mower or place it in the Base
Station for charging.
- Drive the mower manually using the remote control or
carry it by hand for charging in the Base Station.
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow MS1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow MS1000 in the language / languages: English as an attachment in your email.

The manual is 7,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow MS1000

Robomow MS1000 User Manual - German - 54 pages

Robomow MS1000 User Manual - Dutch - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info