644649
40
Zoom out
Zoom in
Previous page
1/52
Next page
40
Display Message Probable Cause/Event Correcve Acons
E 6
Check Drive
- Grass or other object has wrapped
around the drive wheel.
- The drive motors have been
working under severe load for too
long.
- Check the drive wheels and remove the
grass or other objects.
E 7
Front Wheel
Problem
- The Front Wheel has left the
ground for too long during
operation.
- If Robomow has driven onto an obstacle,
Switch off the Safety Switch, raising the front
end: Remove or exclude the object from the
mowing area.
- If Robomow is being used on a slope too
steep for safe mowing, exclude this from the
mowing area.
- If high grass is preventing the front wheel
from fully turning on the ground, raise the
cutting height.
- If the ground contains large holes or
indentations where the front wheel can drop
into when passing across, ll these areas
with dirt and level off.
E 8
Decrease
Inactive Time
- Too many Inactive Days and/or
Hours have been set for your lawn
area. Current settings will not be
changed.
- Mowing Frequency is too high for
current settings of Inactive Time.
The Inactive Time settings will be
set to defaults.
- Area setting is too high for current
settings of Inactive Time. The
Inactive Time settings will be set to
defaults.
- Decrease the number of Inactive Days and/
or the number of Inactive Hours to allow
Robomow to complete mowing your lawn.
- Decrease Mowing Frequency (see p001 in
the table in Section 6.4.2)
- Decrease Area setting
E 9
See
Troubleshooting
in Manual
- E 9 is displayed for all other
messages that are not listed in the
above table.
- Press the ‘Right arrow’ button to receive the
stop reason number and refer to the next
table for more details about the stop reason,
causes, and actions.
9.2 Detailed Error Codes
If the above table (Section 9.1) does not give enough information to help solve the problem, then press the LEFT
arrow while the error code is displayed in order to receive a number that gives more details about the problem
and refer to the table below:
Display Message Probable Cause/Event Correcve Acons
0010
Mow Overheat
- The mowing motor has been
working under a severe load for too
long.
- No need for action – Robomow will renew
automatically the operation after the mowing
motor will cool down.
0011
Drive Overheat
- The drive motors have been working
under a severe load for too long.
- No need to do anything.
- Robomow will renew the operation
automatically as soon as the drive motor will
cool down.
0012
No wire signal - See E3 in the above table
0014
Front wheel
problem
- See E7 in the above table
0015
Button pressed
- One of the operating panel buttons
is constantly pressed.
- Press ‘OK’ to conrm the message and
continue operation. This message is displayed
to inform only.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow MC1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow MC1000 in the language / languages: English as an attachment in your email.

The manual is 3,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow MC1000

Robomow MC1000 Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info