644649
36
Zoom out
Zoom in
Previous page
1/52
Next page
36
Screen Seng Descripon Opons
P024
SmartMow
(Default = OFF)
• Enables the unique SmartMow feature.
• SmartMow feature allows more efcient mowing operation
through the smooth and continuous turns when reaching lawn’s
edge.
• This feature may not be efcient in the same way in every lawn or
in some parts of a particular lawn.
• When this feature is enabled for the rst time in a particular
zone, it may require the mower to cross the lawn and “touch”
the perimeter wire several times (to perform an initial calibration
of the algorithm), before it will start performing smooth turns at
lawn’s edge.
• If there is more than one zone dened, then there is an option
to enable this feature for a particular zone or for the entire lawn
(‘All’).
All
L1/L2/L3
A1/A2/A3/A4
On/OFF
P025
SmartMow
Edge Overlap
(Default = 10)
• Allows adjusting the degree of overlapping with lawn’s edge,
when performing the smooth and continuous turns in SmartMow
mode.
• Increasing this value will cause a higher overlapping with lawn’s
edge (for better mowing results), but at some point may prevent
the mower from performing a smooth turn.
• If there is more than one zone dened, this setting may be set per
zone or for the entire lawn (‘All’).
5-30
P026
TurboMow
(Default = OFF)
• TurboMow feature allows faster and stronger mowing of a high
grass during the rst cut of the season.
• When a mower is operated for the rst time, or if the Factory
Defaults (“Out of the Box”settings – see Section 5.2) are invoked,
this feature is automatically set to ON to provide better mowing
results already after the initial mowing cycle. At the end of the
initial mowing cycle, the feature will be automatically disabled (set
to OFF).
• This menu allows to activate TurboMow feature manually. ‘U094’
(“Raise mowing height when activating the TurboMow mode.”)
will be displayed. At the end of the cycle the feature will be
automatically deactivated (set to OFF).
On/OFF
6.4.3 Robomow App Settings
Using the Robomow App you will have access to additional menu options that are not available on the mower,
such as an option to dene an external setup of a Base Station or an option to set an additional window of
Inactive Hours.
6.5 Operaon in a Non-Base Zone (using a Perimeter Switch)
In order for Robomow to operate in a Non-Base Zone, the Perimeter Switch has to be turned on and the mower
should be inside the active perimeter area.
• Verify that the Perimeter Switch is connected to the zone to be mowed.
• Press the ‘ON’ button to turn on the Perimeter Switch.
• Drive/carry Robomow to the lawn area. Refer to “Transportation” part of Section 1.3 for carrying instructions.
• To initiate the operation, choose the operation mode you want, press the arrow buttons to choose the Zone
you want to mow and press OK to start operation (refer to Section 6.3).
• When Robomow completes the mowing, it will stay on the lawn. You will have to drive/carry it back to its place
for charging.
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow MC1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow MC1000 in the language / languages: English as an attachment in your email.

The manual is 3,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow MC1000

Robomow MC1000 Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info