Manual Roblin Windy Pro 1200 (page 11 of 48) (English, German, Dutch, French, Italian, Spanish)

490283

Zoom out

Zoom in

1/48

Press LED button 5 to obtain the boost position for maximum effect and the LED C will illuminate to

conrm fan is switched ‘ON’.

C – COMPLEMENTARY INSTRUCTIONS

Automatic pre-set stop for the boost speed after 10 mn.

To obtain the best performance it is advisable to switch ‘ON’ the cooker hood a few minutes (in the

boost setting) before you start cooking and you should leave it running for approximately 10 minutes

after nishing.

Press LED button 5 to switch ‘OFF’ the fan motor immediately.

Indication of saturation of the metal grease lters

After 100 hours use, one quick ash of the LED F will indicate that you must clean the metal grease

lters. (See chapter on ‘Maintenance’).

This indication is not available when the fan motor is switched OFF.

Indication of saturation of the active charcoal lter

After 200 hours use, two quick ash of the LEDS F & C will indicate that you must replace the active

charcoal lter and clean the metal grease lters. (See chapter on ‘Maintenance’).

To reset the 200-hour timer the motor and lights must be switched ‘OFF’.

Push the LED button ‘+’ for 10 seconds.

One ash of the LED lights F and C = function is switched ‘OFF’.

Two ashes of the LED lights F and C = function is switched ‘ON’.

To reset the 100 hours timer back to zero requires the motor and lights must be switched ‘OFF’; then

and proceed as follows:

Press the LED button ‘+’ for 3 to 4 seconds and the LED lights F and C will ash to conrm the programme

has been reset to zero.

Instructions for replacing the active charcoal lter are given in the chapter on ‘Recycling’.

Setup Process

Modication: How to adjust the internal microprocessor data to suit the type of motor tted to

this appliance and the supply frequency of 50 or 60 Hz..

1 - Disconnect the cooker hood from the mains supply.

2 - Push the button 0/1 MOTOR.

3 - Reconnect the mains supply while pushing the button 0/1 MOTOR for at least 2 seconds.

4 - Slacken the button 0/1 MOTOR (the Leds ash for about 3 seconds : capacity’s

conrmation SETUP PROCESS).

5 - During the ashing time select the motor type used while pushing one of the 5 buttons

according to the following board:

BUTTON 0/1 Light : Motor FABER 8/28 & 8/50 220-240 V AC / 50 Hz.

BUTTON 0/1 Motor : Motor FABER 8/28 & 8/50 220-240 V AC / 60 Hz.

BUTTON Speed ( - ) : Motor EBM PRO 220-240 V AC / 50 Hz.

BUTTON Speed (+ ) : Motor EBM PRO 220-240 V AC / 60 Hz.

BUTTON Intensive speed : Motor K40 & K50 220-240 V AC / 50 Hz.

REMOTE CONTROL HANDSET

Caution, the remote control must be tted with standard LR03-AAA size 1.5V zinc-carbon alkaline bat-

teries as illustrated Fig. 8. These batteries should give a long life and constant discharge throughout

their life.

These batteries must be disposed of properly and could explode if damaged or exposed to heat.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Roblin Windy Pro 1200 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Roblin Windy Pro 1200 Manual

Product: